2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    2020 SANDVIK DB120 Used 定向钻机2020 SANDVIK DB120 Used 定向钻机
    照片(14)

    2020 SANDVIK DB120

    定向钻机
    CNY ¥1748,377 
    输入的价格为: USD $240,000

    Savona Equipment Ltd.

    联系人:Sales

    Savona, British Columbia, 加拿大 V0K 2J0

    常规

    年限
    2020
    制造商
    SANDVIK
    型号
    DB120
    小时
    423.5
    状况
    二手
    库存号
    1369152
    描述
    Sandvik DB120 Secondary Breaking Drills Quantity: 2 Units Available Make: Sandvik Model: DB120 Commander Year: 2020 and 2019 Hours: Unit 1: Engine: 423.5 Hours Drill: 75.3 Hours Unit 2: Engine: 53.3 Hours Drill: 8.2 Hours Condition: Used, Reported in Good Condition Key Features: Method: Drill - Split Splitter: Hydraulic Wedge Splitting Force: 6,500 kN Drift Size (Min): 3m x 3m Hole Diameter: 48mm Hole Length: 800-1,200mm Control System: Radio Remote Total Weight: 5,600 kg General Model Specifications: Hydraulic Rock Drill: Type: HLX1 (TS2-253) Percussion Power: 6.5kW Operating Pressure: 100 - 180 bar Percussion Rate: 70-88Hz Rotation Torque: 100 Nm (@ 100 bar) Drill Steel: Shank R25 Coupling Sleeve R25 Extension Rod 5’ Button Bit R25 Hole Diameter: 48mm Weight: 50kg Length: 488mm Profile Height: 66mm Shank Lubrication Device: Air/Oil Mist Hydraulic Splitter: Required Hole Diameter: 48mm Length of Wedge: 1,430mm Minimum Hole Depth: 800mm Splitting Force: 6,500 kN Weight: 65kg Max. Pressure: 300 bar Greasing: Automatic Oil Mist Rock Drill Feed: Chain Feed for HLX1: CF300-5’ Feed Length: 2,525mm Rock Drill Travel: 1,300mm Max. Hole Length: 1,200mm Feed/Pull Out Force: 15 kN Splitter Feed: Chain Feed for Splitter: CF300, Splitter Feed Length: 2,180mm Splitter Travel: 1,165mm Boom: Type of Boom: DB300 Special, Articulated Boom Swing: ± 39° Feed Swing: ± 40° Feed Tilt: 104° Hydraulic System: Power Pack: Diesel Engine Percussion Pump: Variable Displacement Pump 2 Gear Pumps Filtration Size: 10 micron (abs) Cooling Capacity: Up to ± 40°C Ambient Hydraulic Oil Tank: 75 Liters Driving, Boom and Drilling: Load Sensing System Flushing System: Flushing: Air Mist Flushing Flushing Air Pressure: 4 -8 bar Compressor: Enduro, 12, Screw Type Compressor Capacity: 2.5m³/min Air Consumption: 250 Nl/min Oil Consumption: 50 - 100 g/h Air Cleaner for Compressor: 1 pc Water Tank: 250 Liters Pressurized, On-Board Max. Water Flow: 1-5 Liters/min Carrier: Type of Carrier: DC302R Special Carrier Type: Rubber Tire, 4-Wheel Drive Oscillation Angles: ± 16° Max Banking: ± 5° Ground Clearance: 380mm Diesel Engine: CAT C4.4, 61 kW, Tier 3, Stage IIIIA Exhaust Catalyzer: Standard Air Cleaner for Engine: 1 pc Transmission: Hydrostatic Tires: 11.5/80 - 15.3 Service Brakes: Spring Applied, Hydraulically Released Tramming Speed: 5.1 km/h (Horizontal) 4.5 km/h (14% = 1:7 =8°) Slow Drive Limited at 1 km/h Gradeability: Max 15° Average Fuel Consumption: 8 - 10 Liters/Hr. Fuel Tank: 100 Liters Fuel Saving System: Standard Handheld Fire Extinguisher: 7.7 or 9 kg (Type ABC) Hydraulic Jacks: 2 x Vertical (Front) 2 x Vertical (Rear) Location: Mexico