8 FUNCTIONS VALVE SPV WITH CANBUS OTTO JOYSTICKS 90L/MIN 12/24 V WITH RADIO CONTROL SCANRECO

阀门

8 FUNCTIONS VALVE SPV WITH CANBUS OTTO JOYSTICKS

90L/MIN 12/24 V WITH RADIO CONTROL SCANRECO

新建

8 Functions Valve with CANBUS Otto Joysticks with cables 90l/min 12/24 V Right and left joystick OTTO MDCi control unit for OTTO joystick interface and button panel for Forest Crane Canbus card Control Panel Radio Remote Control ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Each of the eight operations that are controlled by the two joysticks and the eight valves are 1st Boom – The first section of the Telescopic Boom of the Hydraulic Crane extends to get the load near to it intended destination 2nd Boom – The second section of the Telescopic Boom of the Hydraulic Crane extends to get the load directly above its intended loading/unloading destination Slewing – This controls the rotation of the crane boom to enable the operator to point the boom in the correct direction Support Leg Left – This will stabilise the crane on the left side and is deployed before any lifting begins and retracted after all lifting has been completed Extension – The enables further extension from the crane to give a high level of accuracy Grapple – With this configuration a grapple is included for the forestry application of lifting and moving timber logs Support Leg Right - This will stabilise the crane on the right side and is deployed before any lifting begins and retracted after all lifting has been completed Rotator – The rotator controls the angle and direction of the grapple in order to position it directly above the intended loading/unloading point 2 x Joystick controllers each with forward and reverse, left and right positions in additional to buttons to adjust each specific function to the operator’s specific needs 8 x Function Hydraulic Valves each configured with specific flow rate to suit the required functions. The featured model consists of the following flow rates 1st section 190bar/190bar Flow 80/80l/min 2nd section 230bar/80bar Flow 80/80l/min 3rd section 230bar/180bar Flow 80/80l/min 4th section (P/P)- Flow 40/40l/min 5th section 80bar/80bar Flow 40/40l/min 6th section 190bar/190bar Flow 40/40l/min 7th section (P/P) Flow 65/65l/min 8th section (P/P) ​Flow 65/65l/min ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ CANBus card for analog/digital inputs. DESCRIPTION MDCi is an electronic board with CANBus interface to simulate 2 JC joysticks with 2 Otto joystick and push button dashboard. The transmission has course immediately after the turning on of the electronic card. FEATURES - supply voltage from 10 to 30 Vdc - CAN V2.0B communication bus - 120 Ohm inner terminator not present in this version - 2 diagnostic LEDs (red and green) - firmware updatable by integrated serial port SIGNALS Red LED flashing one time: short circuit error on the +5V stabilized output Red LED flashing two times: one of the analog inputs has been found not at rest position during the turning on, this input is blocked until a reset. Green LED On: the electronic card is working correctly. The green LED flashes one time every time an input (analog or on/off) change status. MDCi contro unit for OTTO joystick interface and button panel for Forest Crane Mounting version: X1 Firmware: mdc_P5_01.hex Cfg file: mdc_P5_01.cfg ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Technical Specifications: Power Supply Voltage : 10Vdc÷30Vdc (inner 5x20 8A fuse type F8A) Current absorpion : 300mA + load outputs (max 7.5A) Wroking Temperature Range : -20 ÷+ 70 C Supply for external poterntiometers: +5V - max current 50mA PWM minimum current range : from 100 to 2500 mA PweM maximum current range: from 100 to 2500mA PWM frequency : 50-60-70-85-100-125-150-200-250-300 Hz Analog inputs impedance: 11 KOhm towards 2.5V Overlall dimensions with connector mounted: 256x210x45mm Drill interasis : 242x142mm (n. 4 holes of 6mm diameter) ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ NOTE: to have the cable L = 1.5m it is necessary to - make the joystick / cable connections 7x0.75mmq by removing the original connector - put the corrugated sheath and fix it to the bottom of the joystick (see photo) - connect the 7x0.75 cable to the Deutsch 6-pin female connector to male contacts ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ Remote Radio Control Scanreco: -1–8 linear levers or 1–4 joysticks. » Various toggle switches, pushbuttons and rotary switches. - Operator feedback by: - LEDs (light emitting diodes) - Monochrome display 2.5" with 128 x64 px - Stop function in accordance with EN ISO 13849-1 cat. 3, PL d. - Cable control: Standard length 10 meters / ~33 ft - Frequency bands: 433–434, 902–928 MHz & 2.4 GHz (other frequencies available on request). - Operating range >100m / > ~330 ft. » Operational temperature: –20°C to +70°C / ~–4°F to +160°F. - Protection category: IP65. » Dimensions: (WxHxD): 350 x160 x190 mm / ~13.78 x6.30 x7.48 in (w/o color display). » Weight: 1.9–2.6 kg / ~4.2–5.7 lbs. including battery