2014 CATERPILLAR D8T WH

2014

CATERPILLAR

D8T WH

10,375

二手

D9643

WARRANTY INCLUDED, Factory Waste Handling (Landfill) Arrangement, CAT C15 ACERT Engine, Block Heater, Cab (ROPS) with A/C, Pressurized Cab Filtration, 28" Trapezoidal Track Shoes, NEW CAT Complete Undercarriage, CAT Semi U Blade with Trash Rack & Wear Plate, Rear Striker Bar/Counterweight Assembly, Final Drive Seal Guards, Clamshell Final Drive Seal Guards, Pivot Shaft Seal Guards, Engine Pre-Cleaner, Auto Reverse Cooling Fan, Debris Resistant Radiator, Fuel Tank Guards, Flood Lighting Package, Bogie Suspension Rollers, Powered Bottom Guards, Rated at 348HP, Weight 86,000 LB, Repair/Condition Report: The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine; At 685 hours, completed 500 hour service At 987 hours, completed 250 hour service At 1,336 hours, completed 1,000 hour service At 1,647 hours, completed 250 hour service At 1,979 hours, completed 500 hour service At 2,363 hours, completed 250 hour service At 2,816 hours, completed 2,000 hour service At 3,232 hours, completed 250 hour service At 3,555 hours, completed 500 hour service At 4,259 hours, completed 250 hour service At 4,346 hours, completed 1,000 hour service At 4,613 hours, completed 250 hour service At 4,982 hours, completed 500 hour service At 5,372 hours, completed 250 hour service At 5,622 hours, completed 2,000 hour service At 6,057 hours, completed 250 hour service At 6,412 hours, completed 500 hour service At 6,675 hours, completed 250 hour service At 6,905 hours, completed 1,000 hour service At 6,905 hours, resealed left track adjuster At 6,905 hours, installed NEW cannon sleeve & seal At 6,905 hours, installed NEW equalizer bar pads At 7,154 hours, completed 250 hour service At 7,418 hours, completed 500 hour service At 7,418 hours, installed UPDATED NRS cooler At 7,418 hours, installed NEW coolant At 7,451 hours, resealed right side track adjuster At 7,451 hours, installed NEW right side cannon seal At 7,695 hours, completed 250 hour service At 7,933 hours, completed 2,000 hour service At 8,207 hours, completed 250 hour service At 8,439 hours, completed 500 hour service At 8,439 hours, resealed right blade lift cylinder At 8,439 hours, resealed blade tilt cylinder At 8,750 hours, completed 250 hour service At 9,068 hours, completed 1,000 hour service At 9,140 hours, cleaned DPF At 9,435 hours, completed 250 hour service At 9,532 hours, resealed left blade lift cylinder At 9,772 hours, REBUILT transmission At 9,772 hours, REBUILT torque converter At 9,772 hours, completed 2,000 hour service At 10,171 hours, completed 250 hour service At 10,171 hours, installed CAT REMAN alternator At 10,174 hours, installed NEW a/c dryer, compressor & accumulator At 10,174 hours, engine was REBUILT & included the following; NEW engine mounts CAT REMAN long block CAT REMAN transmission cooler CAT REMAN engine oil cooler CAT REMAN starter CAT REMAN fuel transfer pump CAT REMAN water pump CAT REMAN turbo NEW damper All NEW sensors NEW exhaust manifolds NEW NRS cooler CAT REMAN fuel injectors Dyno tested engine At 10,174 hours, emission system REBUILT w/; CAT REMAN DPF CAT REMAN ARD head NEW DPF inlet NEW ARD combustion control valve All required emission sensors NEW ECM wiring harness At 10,174 hours, REBUILT both final drives At 10,174 hours, REBUILT diff steering & brake assemblies  At 10,174 hours, REBUILT implement pump  At 10,174 hours, REBUILT steering pump  At 10,174 hours, REBUILT diff steering motor  At 10,174 hours, installed CAT REMAN fan motor  At 10,174 hours, REBUILT hydraulic fan pump  At 10,174 hours, installed NEW fuse block  At 10,174 hours, installed NEW hard nose pins & bushings The following was completed by Marcel Equipment; Upon arrival to our yard, machine was stripped for power washing Machine was inspected visually & operationally Engine oil filter was cut open - clean Transmission filter was cut open - clean Hydraulic filter was cut open – clean Magnets & suction screens checked - clean Final drive oils were checked - levels good & oil clean Engine was serviced The following pressures were taken to ensure within OEM spec; Engine high/low RPM Stall speed Engine oil pressures - high/low  Fuel pressure - high/low Engine boost  Transmission pump pressure Transmission lube pressure - high/low Torque converter inlet & outlet Pilot pressure Main relief pressure Steering stand-by pressure Steering cut-out pressure The following repairs were completed by Marcel Equipment; Removed ripper assembly & installed dog house/striker bar REBUILT seat suspension assembly Installed NEW pivot shaft oil bottle Installed NEW pilot accumulator Serviced & cleaned cab pre-cleaner Serviced & cleaned HVAC system Replaced any required hoses/lines Installed ALL NEW CAT undercarriage Inspected all bogie joints Resealed transmission manifold Installed NEW torque convertor output seal Installed NEW driveshaft u-joints Resealed engine oil pan Installed NEW transmission sensor Inspected all pulleys Serviced electrical box Completed required cab repairs REBUILT & resealed transmission pump Installed NEW hardbar pads Resealed left lift cylinder Serviced a/c system Installed NEW a/c condenser mounts Completed required blade repairs Replaced blade pins/bushings as needed Line bored blade pins bores as needed Assemble blade & install Completed misc repairs Completed required welding/cosmetic repairs Complete machine was sandblasted, primed, painted & new decals applied Machine is now ready to go to work!

封闭式