CMI PVM2500

CMI

PVM2500

104

二手

DP1951

Portable 250-350tph CMI PVM Drum Plant CMI PVM 2500 SUMMARY: This plant is a CMI model PVM 2500 SN# 104,Is rated at 350-450 TPH. The plant is complete (MINUS WIRE). THE PLANT WAS PRODUCING 300 TPH WITH THE 55,000 ACFM BAGHOUSE WITH A LARGER BAGHOUSE PRODUCTION COULD REACH 400-450 TPH. 4 BIN COLD FEED SYSTEM: (Model # PC 432) There are four portable 10’ X 14’ bins with bin dividers for extra capacity. The 30” feeders are 12’ long and are driven by 5 hp AC Lincoln TEFC motors. The 30” collector conveyor powered by a 15 hp motor and folds up for transportation. It feeds onto the 4’ X 12’ Smico single deck screen. Aggregates then feed onto a CMI 30” wide 47’ long, heavy channel frame belt scale conveyor that includes the wind guard and gravity take up. Tandem Axle Configuration. RECYCLE PACKAGE: (NONE) PARALLEL FLOW DRUM: The (2005 CMI model PVM-2500), 9'.6' x 42’ long recycle drum is cradle chain driven by a 100 hp motor and a Dodge TXT-10 gearbox. Both ends of the dryer are expanded for better combustion and mixing. The drum sits on a 24” wide flange beam frame manual legs to grade and steel timber footings. A slinger conveyor that is reversible for calibration introduces materials. The Hauck Starjet is model SJL4580 burning #2 diesel or recycled oil. It is powered by a 100 hp TEFC motor. Tandem Axle POLLUTION CONTROL: (Gencor 54,000 ACFM SN# BH94-7369-92-2A ) The portable Gencor Pulse-Jet baghouse. There is a inlet and outlet duct work with backward inclined fan, Single 200 hp motor, damper and stack are included. Screw auger conveys the dust to a summing auger. The dust is then blown back into the drum with a Gardner Denver pneumatic blower driven by a 25 hp motor. A Sullair 40 HP Screw Compressor delivers air to the on board AIr Storage Tank. There is tandem axle portability. LIQUID ASPHALT STORAGE: There is one portable A.C Tank The A.C. Tank is a (Chattanooga) single compartment 20,000-gallon indirect fired tank with fuel tank built in the goose neck to fuel the hot oil heater. There is a 3" Unloading Pump mounted on the goose neck. All insulated plumbing is included with the plant on the tank to the MISSING heater. There is a 3" metering skid included. There is tandem axle portability with landing pads (NO HEATER) A nominal 10,000-gallon fuel tank sitting on a flat bed trailer with all plumbing in included for recycled oil the pre heater is is included. SILO SYSTEM: The CMI SE 165, SN 121) is portable, 65-ton cable-erect surge silo system with reverse weigh. The 36” x 36” drag slat conveyor is 400+ tph. The twin four inch pitch roller chains use 34” x 7.5” x ¾” slats driven by a 50 hp motor move the materials. There are sliding bearings on the sidewalls that allow the slats to move up and over any floor obstructions. The anti-segregation batcher is mounted on the end of the slat conveyor. The hopper holds a nominal 60-ton capacity. There are heavy steel liners in the cone area. Hydraulic legs push the silo into the erected position. Steel timber footings are provided. An air tank is mounted on the gooseneck. CONTROL HOUSE: The portable, nominal 10’ X 15’ single level, all steel control house has double pane tinted windows.EZ Blend controls manage the plant. This unit is mounted to a trailer with energy center. ENERGY CENTER: (PEC C#H) **The individually bucketed Cutler-Hammer motor controls are in a separable building starters for the plant. The MCC is then located on a stand-alone on CH frame. (There is also a stand-alone 100 kw night time Generator) This plant will need repair. The Drum is missing a Axle, The plant will need some new wire. Location: TX