MARINI MR-C 35

MARINI

MR-C 35

UNKNOWN

New

MARINI MR-C 35 - Call for pricing and additional information Hydraulic Drill Rig mod. MR-C 35, base unit made up of: • Track carriage It is made in steel and is operated by two hydraulic moto reducers provided with negative brake and motion control valve. - Track width: 1200 - 1800 mm - Track wheel base: 1.570 mm - Pad width: 300 mm - Max. speed: 2.0 Km/h - Max climbing ability: 80 %- N.2 frontal stabilizers • Chassis It is made with welded steel sections completed with boom fixing bracket and N.2 rear stabilizers • Hydraulic power pack KOHLER KDI 2404 TCR TIER 4 FINAL - 75 Hp (55Kw) - Diesel engine KOHLER mod. KDI 2404 TIER 4 FINAL 55 Kw (75 Hp) complete of exhaust after treatment with DPF - Electric circuit 24V - Main pump with variable displacement axial piston pump (Load Sensing system) for all positioning functions of the rig including head rotation and feed - Gear pump for oil cooler - Hydraulic filter on pressure and return line - Hydraulic oil tank capacity: 200 lt - Air/oil cooler / Heat exchanger with hydraulic motor - Hydraulic oil temperature and level indicator on tank - Diesel tank capacity: 90 lt - Diesel level indicator on tank • Articulations - Undercarriage rotation (250°) with n.1 turn table with negative brake and check valve - One section boom controlled by hydraulic cylinders - Drilling group rotation +/- 95° by hydraulic turn table - Mast rotation +/- 180° by hydraulic turn table - Mast independent tilting function +/- 15° by hydraulic cylinder - Counter slide with hydraulic cylinder stroke 800 mm • Mast with hydraulic gear reducer feed system - Mast mod. CID 250 made with a rectangular steel frame with reinforced side rails for feed trolley movement and torque support. The mast is completed with a single roller chain and two speed gear reductor with a tractive force of 3500 daN and energy chain - Base mast mod. CID 250 with stroke 1300 mm complete with energy chain (1) - Mast extension lg. 500 mm for stroke 1800 mm using energy chain (1) - Mast extension lg. 2000 mm for stroke 3300 mm complete with energy chain (2) • Carriage for mast CID 250 - Made of welded steel plates completed with 4 rollers and lateral nylon guides - Hydraulic side shift (not usable for short mast setup) • Hydraulic distributors system - Proportional hydraulic distributors HAWE with pressure and flow settings for each valve section (max. operating pressure 450 bar) • Hydraulic and electric setting for “Hydraulic Drifter” - Hydraulic pump and valve complete with electric setting and PLC program for percussion unit (drifter) • Air lubricator - Centralized air lubricator 1"1/2 complete of hydraulic cylinder for air gate/flow control. Capacity 1 lt - Max. Pressure 15 bar • Diesel re-fuel pump - Electric pump for diesel tank re-fuel powered by 24V circuit complete with 3 mt hose and filter • Hydraulic clamp / clamp and breaker mod. 230 - Hydraulic clamp for rods diam. 70 - 230 mm - Hydraulic clamp and breaker for rods diam. 70 - 230 mm Clamping force: 18000 daN Breaking torque: 4.000 daN • Rod guide - Rod guide with interchangeable bushings base 230 Note: The rod guides are complete with one bushing kit, the diameter must be indicated - Interchangeable bushings for rod guide 230 (diameter to be indicated) • Hydraulic winch - Hydraulic winch with self-braking system mod. 500 complete Max. traction: 500 daN Cable length: 20 mt Cable section: 6 mm • Water / Foam pump - Water / Foam pump powered by a hydraulic motor to use with clean water and light polymers (only with rotary mode) Max. flow: 15 lpm Max. Pressure: 100 bar • Controls and Electronic - On board computer for engine management system - On board computer for electric/hydraulic diagnosis system - PLC control with drill rig program for monitoring and safety - Remote control AUTEC (ISO 13849-1) for tracks, positioning and drilling functions with proportional joystick - transmission frequency 2,4 GHz 1 • Basic safety devices - Check valves on all hydraulic cylinders - Emergency stop buttons on drill rig and remote control - Warning labels on the machine - Emergency E-Stop buttons on the clamp- Identification plate without CE marking • Documentation Included with the drilling unit: - N.1 copy of the use and maintenance manual - English - N.1 copy of electric and hydraulic schematic - English - N.1 copy of spare parts manual - English - N.1 USB with all the above manuals and schematics in PDF and engine manual • Painting - Base primer with rust protection - Top coat with lucid finisher - Machine base: GREY RAL 7010 - Details: ORANGE RAL 2011 APPROX. WEIGHT (Depending on accessories): 6.000 - 6.400 kg OPTIONS AND ACCESSORIES • Rotary head / Drifter mounting plate - Mounting plate for Rotary head ID 800 • Rotary head ID 800 - Gear box with double hydraulic motor, series/parallel hydraulic switch complete with flushing swivel 1"1/2 - 630 cc motor (2 Gears) max. torque 1000 daNm - Max speed 90 rpm - Floating spindle kit with springs and shaft API 3"1/2