2018 CATERPILLAR D8T

2018

CATERPILLAR

D8T

7,698

Used

D2380

Neutral Hours: 2,363, CAT C15 ACERT Engine, Engine Block Heater, Powershift Transmission, Cab (ROPS) with A/C, Differential Steer, 28" Track Shoes, Cat Semi U Blade w/ Tilt, Angle Blade With Tilt - 208" Wide - Available, Ripper is Available - Extra, Winch is Available - Extra, Rear Screen, High Speed Oil Change, Engine Air Pre-Cleaner, Reversing Fan, Top Carrier Rollers, Flood Light Arrangement, Rear View Camera, Rated at 364 HP, Weight 82,000 LBS. Repair/Condition Report: The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine; At 652 hours,performed 500 hour service At 1,071 hours, performed 1,000 hour service At 1,515 hours, performed 1,500 hour service At 2,061 hours, performed 2,000 hour service At 3,339 hours, performed 500 hour service At 3,711 hours, installed NEW DPF temp sensor At 3,711 hours, installed NEW ARD spark plug At 3,831 hours, performed 1,000 hour service At 4,412 hours, performed 2,000 hour service At 4,974 hours, performed 500 hour service At 5,525 hours, cleaned DPF At 5,744 hours, installed NEW front crankshaft seal At 5,744 hours, removed, cleaned & pressure tested cooling package At 6,015 hours, REBUILT transmission At 6,015 hours, REBUILT transmission pump At 6,015 hours, REBUILT torque converter At 6,015 hours, installed NEW ARD head At 6,026 hours, performed 2,000 hour service At 6,051 hours, installed NEW a/c compressor & belt At 7,080 hours, installed NEW a/c compressor fan At 7,080 hours, performed 1,000 hour service At 7,692 hours, installed NEW main power relay When unit arrived in yard, MEL had local CAT dealer complete the following; Strip machine for power washing CAT TA inspection Update ECM flash files Cut open all filters & inspect for contaminates - all clean Service emission system if needed - filters, DPF, spark plug, injector etc Inspect magnetic plugs/screens & suction screens - all clean Serviced engine Check oil levels Inspect oils for discolouration Check for logged & active codes for repair Check for applicable service letters Changed engine, final drive, transmission & hydraulic oils Completed the following pressure checks to ensure within OEM spec; Fan pressure & speed Engine RPM high & low idle Engine oil high & low idle pressures Fuel pressure Torque convertor stall speed Full stall boost Implement standby pressure Transmission pump pressure Torque inlet/outlet pressures Torque convertor lock-up clutch Flywheel low pressure - high/low Transmission lube pressure - high/low Performed clutch fill calibration Steering system charge pressure Brake pressure Based on inspection, CAT mechanic completed the following repairs; Installed NEW DEF tank screen & cap Installed NEW DEF injector Installed NEW ARD spark plug Installed NEW fast fill vent Installed NEW pivot shaft oil reservoir bottle Removed cab, torque convertor & engine from machine REBUILT pump drive assembly RESEALED flywheel housing Installed NEW bottom end bearings - main, rod & thrust - with updated bearing kit Installed NEW rear crankshaft seal Resealed oil pan Installed NEW engine mounts Completed engine valve & injector set Disassembled & inspected engine oil pump Installed NEW engine belts Installed NEW engine belt idler pulley Installed NEW hoses/lines within chassis as required Installed NEW EGR cooler pipe Installed NEW heater valves Installed NEW batteries & battery cables Installed NEW service bay harness Installed NEW a/c hoses & dryer Resealed priority housing Installed NEW hoses/lines as required Installed NEW driveshaft u-joints Installed all NEW heater hoses Resealed outlet relief valve & suction tube REBUILT/resealed main hydraulic control valve Stripped & cleaned condenser assembly & fans Resealed blade lift cylinders Marcel Equipment completed the following repairs; Completed required cosmetic & welding repairs Completed required blade repairs Replaced required blade pins & bushings Line bored blade joints where required Prepped machine for sand blasting & painting Sand blasted, primed, painted & detailed Assembled machine once completed Greased machine Machine is now ready to work.

37,194.57 kg

Enclosed

364 HP