建設機械 販売用 From Midway Farm Equipment, Inc. - Mountain Lake, Minnesota

3379 hours, 480/80R42 rear duals, 380/85R30 fronts, Michelin tires, 18x6 powershift, 8.3L Cummins engine, 4 remotes, 1000rpm 1 3/4" pto, 3pt with toplink, clevis hitch, front fenders, local trade, ...See More Details

5294 hours, 480/80R46 duals, 380/85R34 fronts, 18x6 powershift, 4 remotes, 1000 rpm 1 3/4" pto, 3pt, front fenders, LED lights, 15 frt weights, 1000lbs rear wts, radar, shedded, 2nd owner since 200...See More Details

NOW $39,500!! was $49,500,6608 hours, 520/85R42 long axle duals, 420/90R30 fronts, 18x9 powershift trans, 3 remotes, 1000 rpm 1 3/4" pto, HD 3pt,, 14 frt weights, 2 rear wheel wts/side, clevis hitc...See More Details

New HD 8ft 3pt blade, hyd tilt, manual angle, manual offset, 4" kingpin, 5/16"x21 1/2" moldboard, 1/2"x6" reversible cutting edge, Cat 2 or 3, HD blade!!

21ft mast, sideshift, 16.9x24 R4 tires 76%, 12.5x16 rears 1 new, 1 50%, 4 cylinder gas engine, 6000lb lift, owned by our dealership since 1 year old

Lease for $5366/year!! New 15ft windrow stalk chopper, pull type, end drive, 200hp gearbox, 1/4" hood, 1000 rpm 1 3/8" constant velocity pto, 3 groove banded belts, 10" rotor with 2 3/16" bearings,...See More Details

15ft windrow unit, pull type, hyd lift, four 9.5Lx15 tires, small 1000 CV pto, deflectors good, hood has 1 small ding, cup knives ok, 1 owner, 300 acres/year

15ft pull type windrower, small 1000 CV pto, hyd lift, four 9.5Lx15 tires, deflectors good, hood has a few small dings, forming shields have a few welds, cup knives ok

15ft pull type windrow stalk chopper, hyd lift, two transport tires, 9.5x15 tires, cup knives ok, 2nd owner since it was 1 yr old, 200 acres/year

Lease for $6192/year!! New 20ft windrow stalk chopper, pull type, end drive, 200hp gearbox, 1/4" hood, 1000 rpm 1 3/8" constant velocity pto, 3 groove banded belts, 10" rotor with 2 3/16" bearings,...See More Details

20ft pull type stalk chopper, small 1000 CV pto, hyd lift, four 9.5Lx15 tires, hood good, deflectors good, knives ok, faded

5935 hours, 14.9x46 rear long axle duals, 14.9x30 fronts, 4 remotes, 1000 1 3/4" pto, 3pt with QH, 22 frt wts, radar, block heater, JD autotrac steering motor and wiring, no monitor or GPS receiver,

10ft pull type blade, hyd lift, 34" deep, 22" tall, bolt on reversible cutting edge, rigid axle, 15" tires good, clevis hitch

5980 hours, 10x2 powershift trans, 25" tracks, 4 remotes, clevis hitch, radar, block heater, sheetmetal straight, runs good, local trade

NOW $99,500!! was $114,500, 2358 hours, Dyna 6 24x24 partial powershift trans with LH shuttle, ML38 mech self leveling loader, 460/85R38 rears, 380/85R28 fronts, 3 rear remotes, multi-function joys...See More Details

12R22 chopping cornhead, Case IH flagship hookup, hyd stripper plates, single point hookup, side augers, Headsight 2 sensor AHHC, chains tight, sprockets good, snapping roller blades ok, stripper p...See More Details

new 8ft 3pt blade, manual angled adj up to 40 degree, cat 2 hitch, 16" tall moldboard

new 84" box scraper, 6 removeable shanks, 1/2"x6" reversible cutting edge, cat 1 QH ready hitch,

25ft with Crary air reel, gleaner nonsmarttrac hookup, SCH sickle with roller guides, 3 position AHHC, poly skids, std dividers, power reel fore/aft, couple little dings in auger, couple scraps on ...See More Details

8R30, Gleaner R or S series smarttrac hookup, single point hookup, electric adj stripper plates, chains good, sprockets good, snapping roller blades like new, stripper plates ok, 2 sensor Headsight...See More Details

6R30 with Calmer knive rollers, Calmers rollers new 2yrs ago, 550 acres total on Calmers, Gleaner smarttrac hookup, factory poly, chains tight, sprockets good, stripper plates good, ear savers,

6R30 with electric adj stripper plates, Gleaner R or S series Smarttac hookup, poly snouts, single point electrical plug in - no plate, chains tight, sprockets good, stripper plates good, snapping ...See More Details

New 8R30 chopping cornheads, knive rollers blades on snapping rollers, bevel stripper plates, hyd pitch adj, stalk stompers, 2 sensor Headsight AHHC, snout skids, walk platform, row guidance feeler...See More Details

8R30 chopping cornhead, Gleaner R or S series smarttrac hookup, stalk stompers, snout skids, walk platform, Headsight 2 sensor AHHC sensors, Reichardt row guidance wands, 1 owner, used 3 years appr...See More Details

with 1.49% financing!! New 12R30 nonchopping corn head, knife edge snapping roller blades, bevel stripper plates, 2 sensor Headsight AHHC, snout skids, walk platform, Reichardt row guidance feeler ...See More Details