2011 ETI ETT29SNT

2011

ETI

ETT29SNT

中古

8608

動作可能

-2011 Ford F-550 Fiber Splicing Lab Bucket Utility Truck RWD -208K Miles / 8608 Total Engine Hours / 3390 Idle Hours -Triton 6.8L V10 Gasoline Engine -Automatic Transmission -ETI 29' Platform Height / 34' Working Height PTO Boom -Fiber Splicing Lab Body w/ Exterior Utility Doors -Inverter Generator (new) -Coleman Mach AC Unit -110V Plugs, Lights & More Inside Lab -Fiber Door & Work Table -Fleet Maintained & Owned -Ready to Work! -*NEW* inverter generator, front rotors & pads, rear rotor & pads, rear leaf springs & hardware, front wheel bearings, battery, (2) Ford OEM rims & Continental tires, ball joint, carrier bearing, RF radius arm bushing, misc lights & leaks addressed ($11,591 spent mechanical parts & labor) -Please view all 142 pictures and attached video!!!! -Shipping to available to all of USA!! Contact us for a quote! A very nicely sorted and setup fiber splicing truck that is ready to work! This truck runs and drives well. The Triton 6.8L V10 gasoline engine starts right up, sounds good and is very quiet. The automatic transmission shifts through all gears as it should. The ETI 29' platform height / 34' working height bucket unit operates as it should at both control stations (upper bucket control & lower controls). The functionality of the bucket is smooth and stable. It has a hydraulic PTO pump which runs the hydraulics on the boom which is powered by a hydraulic truck mounted PTO. The truck has a new inverter generator installed which powers most accessories inside of the fiber lab. It is a brand new unit that we replaced, has less than 10 total hours on it. The truck is equipped with a fiber splicing lab which has plenty of lights and outlets. When the truck came in it had a significant amount of rust and required attention. Most of the rust has been addressed and the box shows well with new paint/body work. There are a few areas that were cut out and rewelded on the utility box. There is rust present on the cab corners (bubbling), rocker panels (surface rust) and on the underside. Inside of the box shows light wear, but is very nicely sorted and provides ample room to move about. Plenty of storage space and cabinets. The interior splice lab height is plenty to stand up in and work out of. It also has exterior tool boxes which are in nice condition inside and out, the box construction is solid. The lab has two splice doors. The exterior is in good condition with cosmetic flaws to be expected for the year / miles of the truck. The interior is in good condition but does show wear on par for the mileage. The frame shows good but does have surface rust/minor scaling. All tires appear to be in good, workable condition with deep tread remaining, the fronts are new. No warning lights are illuminated on the dash. This is a hard to find truck that is well optioned and ready to go. Great truck that you could hop in and get right to work. This truck has been used so please expect small damages, surface rust and imperfections. Nothing is stopping this truck from being put right into service and its a great opportunity to get a good truck!! This truck is on our lot and ready for sale NOW, buy and pick up the same day! Trucks have been selling faster than we can list them so do not hesitate to reach out. This truck has been mechanically checked and the oil has been changed, fly in and drive it home. Please view all pictures and attached video for an accurate representation of the truck. We are located in Clarksville, MD 21029. For any further questions or a shipping quote feel free to contact us. Thank you for looking.

2011

FORD

F550 XL SD

1FDUF5GY1BEA42235

334,044 km

正確/確かめ

Ford

ガソリン

2WD

オートマティック

スプリング

Single

8,164.66 kg

Utility

8.84 m

10.36 m

Telescopic

One Man

はい

Good

はい