2021 FAB TEC INC 7203

2021

FAB TEC INC

7203

P-7-20-3-566-21

中古

E00069691

PORTABLE 7’ X 20’ 3 DECK SCREEN PLANT WITH (3) CROSS CONVEYORS AND 42" FEED CONVEYOR EQUIPPED PER THE BELOW: - 7’ X 20’ - 3 JCI DECK SCREEN, 50 HP 1200 RPM TEFC - COIL SPRINGS - 4FT PANELS - SIDE TENSIONED BOTTOM DECK - JCI BASE FRAME 3 AXLE CARRIER: - 18" WF BEAM 60# - HUTCH 61" SPAN EQUALIZING SUSPENSION - 22,500# STANDARD FORGE AXLES, 11:00R X 22.5 TIRES - AIR BRAKES, LED BRAKE LIGHTS, LED MARKER LIGHTS, LED STROBE LIGHT, REFLECTOR - APE, AND MUD FLAPS 60" X 29' UNDER SCREEN CONVEYOR; 20 HP TEFC: - 42" SPACING ON CEMA C IDLERS - SEW RIGHT ANGLE DRIVE, TYPE “E” BEARINGS - VULCANIZED LAGGED HEAD PULLEY, SELF-CLEANING WING TAIL PULLEY - 3 PLY BELT, 3/16 X 1/16 COVER - VULCANIZED SPLICE - SUPERIOR EXTERRA BELT SCRAPER - 1/4" PLATE UNDER SCREEN HOPPER WITH WEAR STRIPS & ADJUSTABLE SKIRT BOARD WIPERS. - HEAVY DUTY 12" WF SUPPORT STAND UNDER SCREEN (2) 30" X 12' CROSS CONVEYORS FOR 1ST & 2ND DECK. (1) 24" X 12’ FOR 3RD DECK: - 7.5 HP TEFC MOTORS WITH SEW RIGHT ANGLE DRIVES - CHANNEL INSET IDLERS - VULCANIZED LAGGED HEAD PULLEY AND SELF CLEANING WING TAIL PULLEY - DODGE SCM BEARINGS - 2 PLY 3/16" COVER BELT, 3 PLY ON 1ST DECK CONVEYOR - VULCANIZED SPLICES - SELF CLOSING SAFETY GATE AT LADDER OPENING 42" FEED CONVEYOR WITH OPTIONAL ADJUSTABLE FEED HEIGHT; 20 HP: - SEW RIGHT ANGLE DRIVE - CLOSE SETTING IMPACT IDLERS IN FEED AREA, THEN 36" C/C FOR CEMA C CIT IDLERS - DODGE SCM BEARINGS - 3 PLY BELT WITH 1/4” COVER - VULCANIZED LAGGED HEAD PULLEY AND SELF-CLEANING WING TAIL PULLEY - 5' RECEIVING HOPPER WITH ADJUSTABLE WIPERS & FULL-LENGTH SKIRT BOARD - PPI IMPACT SYSTEM IN LIEU OF IMACT IDLERS IN LOAD ZONE - VULCANIZED SPLICE - AR LINED PRODUCTS DISCHARGE CHUTES - 20" FOLD DOWN WALK WAYS BOTH SIDES OF SCREEN - 48" BACK PLATFORM, TOE BOARDS, 42" TUBESTEEL HANDRAILS, AND ACCESS LADDER - SAFETY GUARDS, SANDBLASTED CHASSIS, RUST INHIBITOR PRIMER, AND TWO FINISH COATS OF PAINT INCLUDED. INCLUDED OPTIONS: - FAB TEC PLANT MOUNTED 48K RUN-ON SYSTEM - 5 X 24" CYLINDERS 48,000 LB. CAPACITY (AT 2500 PSI) WITH SAFETY-LOK CIRCUIT - DELTA HPX-200 12-VOLT POWER UNIT - (1) SPOOL VALVE~ NUMBER OF BANKS TO MATCH LEG QUANTITY - CYLINDER MOUNTING PLATES & HARDWARE - HEAVY DUTY FOOT PADS SELF CONTAINED HONDA 8 HP HYD. POWER PACKAGE ~VS~ HPX 200 12V: - ELECTRIC START - 12 GALLON HYDRAULIC RESERVOIR WITH FILTER PROTECTION - 2 1/2 GPM PUMP HYDRAULIC LIFT AT HEAD END OF FEED CONVEYOR: - TO LIFT CONVEYOR FOR SCREEN CLOTH INSTALLATION & MAINTENANCE HYDRAULIC LIFT AT TAIL END OF FEED CONVEYOR: - PIN LOCATIONS AT DIFFERENT LEVELS - 1/3 – 2/3 PANEL STYLE BLENDING - 1ST TO 2ND AND 2ND TO 3RD DECK - VULCANIZE SPLICE ON ALL CONVEYORS - 42” SUPERIOR EXTERRA BELT SCRAPER ~VS~ STANDARD COMBI-WIPE - 60” SUPERIOR EXTERRA BELT SCRAPER ~VS~ STANDARD COMBI-WIPE - SEW KA77 7.5 HP RIGHT ANGLE DRIVE ~VS~ CONVENTIONAL DRIVES ON ALL CROSS CONVEYORS - INCLUDES TYPE “E” BEARINGS ON HEAD PULLEY - SEW KA97 20 HP RIGHT ANGLE DRIVE ~VS~ CONVENTIONAL DRIVE - INCLUDES TYPE “E” BEARINGS ON HEAD PULLEY - TOOL BOX MOUNTED ON CHASSIS - RUBBER DISC RETURNS ~VS~ STEEL CANS ON ALL CONVEYORS PROVISION FOR SLIDE-IN REJECT CONVEYOR: - SIMPLY FLAT BAR STYLE - CONVEYOR NOT INCLUDED - TIE OFF CABLES INSTALLED ON BOTH ENDS OF SCREEN SUBFRAME - FAB TEC IS NOT RESPONSIBLE IF TIE OFFS DON’T MEET MSHA CODE - ORANGE GUM RUBBER FLASHING ON ALL CONVEYORS - 3 PLY BELT ON UNDERSCREEN CONVEYOR. - PROVISION FOR SLIDE IN REJECT CONVEYOR - GUARDING - WE DO NOT WARRANT THAT MANUFACTURERS’ GUARDING WILL MEET ALL LOCAL CODES. IT IS THE RESPONSIBILITY OF THE END USER TO HAVE GUARDING CHECKED BY A LOCAL INSPECTOR, PRIOR TO STARTUP OF EQUIPMENT OPERATIONS, CORRECTIVE ACTIONS AND ASSOCIATED EXPENSE ARE THE RESPONSIBILITY OF THE END USER.