価格はお問い合わせください
Machine Location:1000 Progress DriveLondon, Ontario, カナダ N6N 1B8(Opens in a new tab)
売主に関する情報
View Seller InformationGeneral
年式
2014
メーカー
CATERPILLAR
モデル
D8T WH
時間
10,375
状態
中古
ストック番号
D9643
説明
WARRANTY INCLUDED, Factory Waste Handling (Landfill) Arrangement, CAT C15 ACERT Engine, Block Heater, Cab (ROPS) with A/C, Pressurized Cab Filtration, 28" Trapezoidal Track Shoes, NEW CAT Complete Undercarriage, CAT Semi U Blade with Trash Rack & Wear Plate, Rear Striker Bar/Counterweight Assembly, Final Drive Seal Guards, Clamshell Final Drive Seal Guards, Pivot Shaft Seal Guards, Engine Pre-Cleaner, Auto Reverse Cooling Fan, Debris Resistant Radiator, Fuel Tank Guards, Flood Lighting Package, Bogie Suspension Rollers, Powered Bottom Guards, Rated at 348HP, Weight 86,000 LB,
Repair/Condition Report:
The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine;
At 685 hours, completed 500 hour service
At 987 hours, completed 250 hour service
At 1,336 hours, completed 1,000 hour service
At 1,647 hours, completed 250 hour service
At 1,979 hours, completed 500 hour service
At 2,363 hours, completed 250 hour service
At 2,816 hours, completed 2,000 hour service
At 3,232 hours, completed 250 hour service
At 3,555 hours, completed 500 hour service
At 4,259 hours, completed 250 hour service
At 4,346 hours, completed 1,000 hour service
At 4,613 hours, completed 250 hour service
At 4,982 hours, completed 500 hour service
At 5,372 hours, completed 250 hour service
At 5,622 hours, completed 2,000 hour service
At 6,057 hours, completed 250 hour service
At 6,412 hours, completed 500 hour service
At 6,675 hours, completed 250 hour service
At 6,905 hours, completed 1,000 hour service
At 6,905 hours, resealed left track adjuster
At 6,905 hours, installed NEW cannon sleeve & seal
At 6,905 hours, installed NEW equalizer bar pads
At 7,154 hours, completed 250 hour service
At 7,418 hours, completed 500 hour service
At 7,418 hours, installed UPDATED NRS cooler
At 7,418 hours, installed NEW coolant
At 7,451 hours, resealed right side track adjuster
At 7,451 hours, installed NEW right side cannon seal
At 7,695 hours, completed 250 hour service
At 7,933 hours, completed 2,000 hour service
At 8,207 hours, completed 250 hour service
At 8,439 hours, completed 500 hour service
At 8,439 hours, resealed right blade lift cylinder
At 8,439 hours, resealed blade tilt cylinder
At 8,750 hours, completed 250 hour service
At 9,068 hours, completed 1,000 hour service
At 9,140 hours, cleaned DPF
At 9,435 hours, completed 250 hour service
At 9,532 hours, resealed left blade lift cylinder
At 9,772 hours, REBUILT transmission
At 9,772 hours, REBUILT torque converter
At 9,772 hours, completed 2,000 hour service
At 10,171 hours, completed 250 hour service
At 10,171 hours, installed CAT REMAN alternator
At 10,174 hours, installed NEW a/c dryer, compressor & accumulator
At 10,174 hours, engine was REBUILT & included the following;
NEW engine mounts
CAT REMAN long block
CAT REMAN transmission cooler
CAT REMAN engine oil cooler
CAT REMAN starter
CAT REMAN fuel transfer pump
CAT REMAN water pump
CAT REMAN turbo
NEW damper
All NEW sensors
NEW exhaust manifolds
NEW NRS cooler
CAT REMAN fuel injectors
Dyno tested engine
At 10,174 hours, emission system REBUILT w/;
CAT REMAN DPF
CAT REMAN ARD head
NEW DPF inlet
NEW ARD combustion control valve
All required emission sensors
NEW ECM wiring harness
At 10,174 hours, REBUILT both final drives
At 10,174 hours, REBUILT diff steering & brake assemblies
At 10,174 hours, REBUILT implement pump
At 10,174 hours, REBUILT steering pump
At 10,174 hours, REBUILT diff steering motor
At 10,174 hours, installed CAT REMAN fan motor
At 10,174 hours, REBUILT hydraulic fan pump
At 10,174 hours, installed NEW fuse block
At 10,174 hours, installed NEW hard nose pins & bushings
The following was completed by Marcel Equipment;
Upon arrival to our yard, machine was stripped for power washing
Machine was inspected visually & operationally
Engine oil filter was cut open - clean
Transmission filter was cut open - clean
Hydraulic filter was cut open – clean
Magnets & suction screens checked - clean
Final drive oils were checked - levels good & oil clean
Engine was serviced
The following pressures were taken to ensure within OEM spec;
Engine high/low RPM
Stall speed
Engine oil pressures - high/low
Fuel pressure - high/low
Engine boost
Transmission pump pressure
Transmission lube pressure - high/low
Torque converter inlet & outlet
Pilot pressure
Main relief pressure
Steering stand-by pressure
Steering cut-out pressure
The following repairs were completed by Marcel Equipment;
Removed ripper assembly & installed dog house/striker bar
REBUILT seat suspension assembly
Installed NEW pivot shaft oil bottle
Installed NEW pilot accumulator
Serviced & cleaned cab pre-cleaner
Serviced & cleaned HVAC system
Replaced any required hoses/lines
Installed ALL NEW CAT undercarriage
Inspected all bogie joints
Resealed transmission manifold
Installed NEW torque convertor output seal
Installed NEW driveshaft u-joints
Resealed engine oil pan
Installed NEW transmission sensor
Inspected all pulleys
Serviced electrical box
Completed required cab repairs
REBUILT & resealed transmission pump
Installed NEW hardbar pads
Resealed left lift cylinder
Serviced a/c system
Installed NEW a/c condenser mounts
Completed required blade repairs
Replaced blade pins/bushings as needed
Line bored blade pins bores as needed
Assemble blade & install
Completed misc repairs
Completed required welding/cosmetic repairs
Complete machine was sandblasted, primed, painted & new decals applied
Machine is now ready to go to work!
Exterior
ROPS
Enclosed