価格はお問い合わせください
売主に関する情報
View Seller InformationGeneral
メーカー
SUPERIOR
モデル
8X16
シリアル番号
2285986
状態
新品
ストック番号
1344
説明
Equipment As Follows:
Carrier Chassis
Construction- Heavy duty wide flange beam
Axle- Single, with dual 11x22.5 tires
Landing Legs- Crank-down
Fifth Wheel- included
Brakes- complete air brake package
Lights- brake and directional signals
Mud Flaps- installed behind transport wheels
Frame Skirting- sheet metal side guard runs full length of hopper, under trailer frame; front section folds up for transport. Both sides.
Hopper Specifications
Hopper Size- 8’ x 16’ top opening
Hopper Construction- fabricated with ¼” plate, reinforced around top and bottom
Hopper Capacity- 10 cubic yards struck
Bottom Opening- tapered, with I-beam breaker bar
Hopper Skirting- sheet metal side guard runs full length of hopper for protection for belt feeder, both sides
Grizzly Configuration
Grizzly Bars- triangle bars; 3/4” x 4” flat bars on top with 3/8” x 4” flat side bars, adjustable spacing
Grizzly Dump- Grizzly raises and lowers hydraulically, 15hp electric pumping unit, electrical controls
Bar Spacing- 4” spacing between grizzly bars
Self Relieving- not included
Bi-Directional- Grizzly dumps to either side
Remote Control- included
Belt Feeder
Belt Feeder Size- 36” wide x 18’ long
Belt Feeder Drive- Class I head end
Belt Feeder Gear Reducer- dodge shaft mount
Belt Feeder Motor- 15 HP
Belt Feeder V-Belt Drive- with drive guard
Belt Feeder Capacity- 250-850 STPH of 100 PCF material, 25o surcharge (90% fines, 10% spherical lumps 4” minus)
Belt Feeder Speed- variable, from 24 to 95 FPM
Belt Feeder Idlers- Superior CEMA C, 5” dia. steel rolls, sealed for life ball bearings
Flat Carrier- 7” spacing
Belt Feeder Returns- steel rolls, on 10’ spacing
Belt Feeder Scraper- Superior Exterra Primary
Discharge Conveyor
Size- 36” wide x 40’ long
Drive- Class I head end
Back Stop- installed in reducer
Motor- 20 hp
V-Belt Drive- with drive guard
Capacity- 850 STPH of 100 PCF material, 25o surcharge (90% fines, 10% lumps 4” minus)
Belt Speed- 350 fpm
Idlers- Superior CEMA B, 5” dia. rolls, sealed for life ball bearings
Load Area- 20o trough, 12-16” spacing
Trough- 35o on 4’ spacing
Returns- steel rolls, on 10’ spacing
Gathering Trough- with adjustable rubber flashing
Rock Guard- entire length of conveyor
Belt Scraper- not included
Raise- manual
Guarding- for drive and tail pulley’s, v-belt drive and return idlers. Guards may not meet all local codes; customer is responsible to have guarding inspected.
Conveyor Components
Drive Pulley- 14” diameter, 3/8” herringbone lagged drum
Tail Pulley- 14” diameter, MD Chevron pulley
Shafts- turned and polished
Bearings- dodge
Take Ups- screw type
Belting- 3-ply 3/16 x 1/16 330 PIW
Belt Splice- factory vulcanized splice
Electrical Specifications
Voltage- 480 v / 3 ph / 60 hz
Electrical- enclosure with main disconnect, circuit breaker, and controller for variable frequency drive
Paint
Paint- 1 coat primer, 1 coat finish enamel, Superior Beige 12-00619
Guard Paint- Yellow
Idler Paint- powder coat Superior Orange
Sign Plate- RB Scott sign plate installed
On-Site Start-up, Training and Warranty Commissioning
• RB Scott will supply a field service technician to complete startup