MARINI MR-C 50

MARINI

MR-C 50

UNKNOWN

新品

MARINI MR-C 50 - Call for pricing and additional information - Call for pricing and additional information Hydraulic Drill Rig mod. MR-C 50, base unit made up of: • Track carriage It is made in steel and is operated by two hydraulic moto reducers provided with negative brake and motion control valve. It is made in steel and is operated by two hydraulic moto reducers provided with negative brake and motion control valve. - Variable track width with hydraulic cylinders: 1.350 - 1.850 mm - Track wheelbase: 1.700 mm - Pad width: 300 mm - Max. speed: 2.0 Km/h - Max climbing ability: 80 % - N.2 frontal stabilizer - N.2 rear stabilizes • Chassis It is made with welded steel sections completed with distributors and electric components box including boom fixing frame. • Hydraulic power pack JOHN DEERE 4045 HFC04 Tier IV Final - 140 Hp / 104 Kw. -Diesel engine JOHN DEERE mod. 4045 HFC04 Tier IV final 104 Kw (140 Hp) complete of exhaust system (DPF) and Adblue -Electric circuit 24V -Main pump with variable displacement axial piston pump (Load Sensing system) for all positioning functions of the rig including head rotation and feed -Gear pump for oil cooler -Hydraulic filter on pressure and return line -Hydraulic oil tank capacity: 300 lt -Air/oil cooler / Heat exchanger with hydraulic motor -Hydraulic oil temperature and level indicator on tank -Diesel tank capacity: 150 lt - Diesel level indicator on tank -Diesel level indicator on tank • Articulations -Boom rotation of +/- 30° (left / right) by two hydraulic cylinders - One section telescopic boom (400 mm ) controlled by hydraulic cylinder -Drilling group rotation +/- 95° by hydraulic turn table with n.2 motors -Mast rotation +/- 180° by hydraulic turn table with n.2 motors -Mast independent tilting function +/- 15° by hydraulic cylinders -Counter slide with hydraulic cylinder stroke 800 mm • Mast with hydraulic gear reducer feed system -Mast mod. CID 300 made with a rectangular steel frame with reinforced side rails for feed trolley movement and torque support. The mast is completed with a single roller chain and two speed gear reductors with a tractive force of 5000 daN and energy chain. A - Mast mod. CID 300 with stroke 3500 mm • Carriage for mast CID 300 -Made of welded steel plates completed with 4 rollers and lateral nylon guides -Hydraulic side shift for head / drifter lateral movement • Hydraulic distributors system - Proportional hydraulic distributors HAWE with pressure and flow settings for each valve section (max. operating pressure 450 bar) • Hydraulic and electric setting for “Hydraulic Drifter” - Hydraulic pump, valve and electric setting with PLC program for percussion unit (drifter - size RH 10X) • Rotary head / Drifter mounting plate - Mounting plate for rotary head EURODRILL RH 10X • Rotary head EURODRILL RH 10X -Gear box with double hydraulic motor, series/parallel hydraulic switch complete with drive flange type B -HP 98 motor (2 speed) max. torque 1100 daNm - Max speed 86 rpm -Flushing head (Swivel) with connection G2" -Drive flange with API 3"1/2 connection • Percussion kit for rotary head EURODRILL RH 10X -Percussion unit type 40, f = ... 2400 min-1; We = ... 500 Nm -Mechanical damping system with return percussion impulse -Shank adaptor with male thread H64 (LH) -Shank adaptor with integrated flushing diam. 100 mm with flushing connection 1"1/2 leaving with R51 LH box (other options available) • Hydraulic clamp / clamp and breaker mod. 230 -Hydraulic clamp for rods diam. 70 - 230 mm -Hydraulic clamp and breaker for rods diam. 70 - 230 mm Clamping force: 18000 daN Breaking torque: 4.000 daN/m Note: The clamps are complete with blocks for DTH rods/casings Clamp inserts for hollow bars 30 - 90 mm • Rod guide - Rod guide with interchangeable bushings base 230 mm Note: The rod guides are complete with one bushing kit, the diameter must be indicated. - Interchangeable bushings for rod guide 230 (diameter to be decided by the client) • Air lubricator - Centralized air lubricator 1" 1/2 with hyd. cylinder for air gate/flow control. Cap. 8 lt -Max. Pressure 24 bar • Hydraulic winch -Hydraulic winch with self-braking system mod. 1000 complete with steel cable, derrick and control valve Max. traction: 1000 daN Cable length: 20 m Cable section: 8 mm • Water / Foam pump Water / Foam pump powered by an hydraulic motor to use with clean water and light polymers Max. flow: 30 lpm Max. Pressure: 150 bar • Pressure lance and drum for machine cleaning •Controls and Electronic -On board computer for engine management system -On board computer for electric/hydraulic diagnosis system -PLC control with drill rig program for monitoring and safety -Remote control AUTEC KFMA99KHO (ISO 13849-1) for tracks, positioning and drilling functions with proportional joystick - transmission frequency 2,4 GHz • Basic safety devices -Check valves on all hydraulic cylinders -Emergency stop buttons on drill rig and remote control -Warning labels on the machine -Emergency E-Stop buttons on the clamp- Identification plate without CE marking • Documentation Included with the drilling unit: -N.1 copy of the use and maintenance manual - English version. -N.1 copy of electric and hydraulic schematic - English version. -N.1 copy of spare parts manual - English version. -N.1 USB with all the above manuals and schematics in PDF and engine manual • Painting -Base primer with rust protection -Top coat with lucid finish -Machine base: GREY RAL 7010 - Details: ORANGE RAL 2011