JPY ¥59,953,259
Rental Prices:
Monthly: JPY ¥2,553,705
(入力された価格 USD $16,500)
Lease Prices:
Monthly: JPY ¥1,139,107 / 60 Month Lease
(入力された価格 USD $7,360)
売主に関する情報
View Seller InformationMurrysville Machinery Company, LLC
お問い合わせ先:Equipment Sales
電話番号:+1 724-361-8011
New Stanton, Pennsylvania, アメリカ 15672
Rental Contact Information
Murrysville Machinery Company, LLC
お問い合わせ先:Jason Micale
電話番号:+1 724-361-8011
New Stanton, Pennsylvania, アメリカ 15672
General
年式
2022
メーカー
ASTEC
時間
656
モデル
1822PH
シリアル番号
420377
状態
中古
説明
Screen
6’ x 16’, 3-deck horizontal wet vibrating screen
V-belt drive assembly with 40-HP, 1200 RPM motor
Huck-bolted assembly
1/4” plate steel side plates
160-mm double-roll spherical self-aligned bearings
Triple shaft vibrating mechanism complete with keyless holdfast hub locking assembly
Oval motion stroke pattern
Adjustable stoke amplitude (3/8” - 5/8”)
Adjustable stoke angle (30° - 60° in 5° increments)
Adjustable speed via adjustable motors heave (675 - 875
RPM)
Fully contained oil splash lubrication system
Bolt-on tailgates, 24” feedbox and 4” discharge lips
Steel coil springs
Side tension draw bar screen cloth retention systemSpiral pipe - heavy wall 14” dia.
Fine Material Washer
5036-25T (36” twin) fine material washer
Tank is of 3/16” (sides and bottom) and 3/8” (rear end
plate) welded plate steel construction and includes a curved
bottom with integral rising current manifold (4” dia. inlet)
Large undisturbed pool area with adjustable weir boards
and overflow flume with 10” dia outlet
Double pitch, solid flight spiral assembly with standard AR
steel inner wear shoes and standard urethane outer wear
shoes
Greaseable, externally mounted Dodge Imperial E tail end
flange bearing; greaseable Dodge pillow block head end
bearing
Lower end seal - chrome plated stainless steel wear sleeve,
water tight bellows type rubber seal and secondary grease
seal
High efficiency v-belt drive assembly (one drive assembly
per spiral) includes 15-HP TEFC motor and Dodge TA-II
double reduction shaft mount reducer
Tapered discharge chute set at 45º angle to gradeHigh efficiency v-belt drive assembl
Chassis
Heavy duty 12” I-beam construction
Tandem walking beam axle arrangement with dual Dana
22,000# axles and eight (8) 11:00 x 22.5 tires
Fifth wheel king pin, air brakes, travel lights, mudflaps and
cribbing locations14-1/2” dia. feed inlet
Water System
All fresh water plumbing to a single 6” inlet located near the
tail end of the fine material washer
Fine material washer manifold includes a 4” butterfly valve,
4” swing check valve and pressure gauge
1”chase water plumbing with gate valves
Screen manifold with flow control valves for each spray bar
Fourteen (14) spray bars each with nineteen (19) 10.0 gpm
(@ 40 psi) spray nozzles
3” connection on the screen manifold for the optional feed
box
Screen Chutes /Fines Hopper
3/16” A36 welded plate steel construction
Chutes allow for positioning of three (3) radial stackers under
the chutes
Fines hopper transitions to form the feed box and baffle plate
of the 36” single fine material washer
Access
28-1/2” wide access platform with 1-1/2” OD handrails
and toeboards across the feed end of the screen
19” wide access platform with 1-1/2” OD handrails and
toeboards along both sides of the screen
Ladder access from grade which can be located on either
side of the plant