2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent2021 IROCK ITC300 Used 岩石骨材破砕設備 for rent
    Photos(9)

    2021 IROCK ITC300

    岩石骨材破砕設備
    USD $775,000 
    Rental Prices:
    Monthly: USD $35,000
    Lease Prices:
    Call For Availability

    売主に関する情報

    View Seller Information

    Maxim Equipment

    お問い合わせ先:Joe Jensen

    電話番号:+1 209-781-4068

    Ripon, California, アメリカ 95366

    visit our website (Opens in a new tab)

    Rental Contact Information

    Maxim Equipment

    お問い合わせ先:Joe Jensen

    電話番号:+1 209-781-4068

    Ripon, California, アメリカ 95366

    visit our website (Opens in a new tab)

    General

    年式
    2021
    メーカー
    IROCK
    時間
    2,360
    モデル
    ITC300
    シリアル番号
    92011
    状態
    中古
    ストック番号
    211004 CC10
    説明
    CRUSHING CHAMBER… Metso HP300 Cone Crusher Feed opening: 41” (1050mm) Crusher input speed: 750 - 950 rpm Crusher Drive: Direct drive Closed side setting adjustment: Hydraulic Level sensor: Ultrasonic Throw: 3.3” (84 mm) at discharge with new liners Power required: 300 Hp FEEDER… Feeder opening width: 36” (910 mm) Feeder drum crs.: 19’ – 8.2” (6.0 m) Drive: Hydraulic Feeder belt width: 48” (1200 mm) Motor: Danfoss OMSS 125 Gearbox: Bonfig 809 W2 24.2:1 Flow rate: 33.8 GPM (128 LPM) Adjustable speed: Yes Maximum speed: 42 rpm HOPPER… Length: 12’ – 4.9” (3.78 m) Width: 7’ – 2” (2.2 m) Volume: 6.5 yd3 (5 m3) levelled off, 8.1 yd3 (6.2 m3) heaped Material: ¼” sides + 3/8” Hardox® liners MAIN CONVEYOR… Stockpile height: 12’ – 9” (3.887 m) Belt width: 48” (1200 mm) Belt spec: Plain 500/3 8+2 Drive drum dia.: 13.7” (350 mm) Tail drum dia.: 10.6” (270 mm) Motor: OMV800 Flow rate: 23.7 GPM (89.6 LPM) Maximum speed: 112 rpm Angle adjustable: YES Quick release: YES POWERUNIT AND HYDRAULICS Engine: Volvo D13 Tier 5 Engine power: Volvo - 380 Kw (510HP) Engine speed: 1570 - 1900 rpm Cone drive clutch: PT-tech HPTO14TF1 Flywheel Pump 1 (Tracks/Feeder): Kawasaki K3VL80 Flywheel Pump 2 (Tracks/Main conveyor): Kawasaki K3VL80: LH PTO Pump 3 (Auxiliary/Lube/pilot): Turolla 29/29/10 Total system flow (max): 88.5 GPM (335 LPM) Hydraulic tank capacity: 211 gal (800 L) ELECTRICS… Emergency stops: 4 off, 2 feeder, 2 power unit Chassis cabling: Armored cable Start Siren: YES – 10 sec delay Control panel: Tedd Engineering / IFM Engine shutdowns: • Low oil pressure • High water temp • Air filter blockage (selectable) • Fuel contamination • Low hydraulic tank level • Low lube oil flow • Low lube oil pressure • High lube oil temperature • High hydraulic oil temperature Radio control tracks and feeder: STANDARD Pendant track control: YES – plugged in control cabinet TRACKS… Width: 15.7” (400 mm) Length: 13’ – 5.4” (4.1 m) crs Height: 32” (817 mm) Gearbox: Bonfiglioli 711 Ratio: 144:1 Motor: Rexroth A2FE90 Speed max: 0.93 mph (1.50 kph) Flow rate: 40.2 GPM (152 LPM) Multiple speeds: Three speed system selectable at control panel with smooth start / stop CAPACITIES… Diesel tank capacity: 290 gal (1100 L) Hydraulic tank capacity: 211 gal (800 L) SAFETY FEATURES… External belt alignment points External grease points Engine safety shutdown systems Full safety guarding for nip points