THB ฿35,038,602
Seller Information
View Seller InformationGENERAL EQUIPMENT & SUPPLIES INC
Contact:Sales Department
Phone:+1 701-213-4058
Fargo, North Dakota, USA 58103
General
Year
2024
Manufacturer
FAB TEC INC
Model
3055R
Serial Number
PC-30-55-446-24
Condition
New
Stock Number
E00067937
Description
PORTABLE 30 X 55 SUPERIOR JAW PLANT WITH 54” X 26’ UNDER JAW CONVEYOR AND SUPERIOR 54" X 20' VGF WITH OPTIONS EQUIPPED PER THE BELOW:
4 AXLE CARRIER 24" 76# WF BEAMS:
- HUTCH EQUALIZING 9700 SUSPENSION. TANDEM/TANDEM.
- 22,500# STANDARD FORGE AXLES 10' TREAD.
- 11:00R X 24.5 TIRES.
- 4 GROUND SUPPORT STANDS WITH JACKING LEGS.
- FRONT HEAVY DUTY FOLD-DOWN LEGS.
- AIR BRAKES, LED BRAKE LIGHTS, LED MARKER LIGHTS, LED STROBE LIGHT, REFLECTIVE
TAPE, AND MUD FLAPS.
- HEAVY DUTY REAR STRUCTURE FOR OPTIONAL BOOSTER ATTACHMENT. (BOOSTER
ATTACHMENT NOT INCLUDED, OPTIONAL)
- WEG 150 HP 1200 RPM 447T TEFC WITH 10 GROOVE 8V-BELT DRIVE.
- CRUSHER FRAME MOUNTED PIVOT STYLE MOTOR MOUNT. 5V DRIVE BELTS WITH ENCLOSED
GUARDS.
SUPERIOR LIBERTY 30 X 55 JAW CRUSHER, 3” X 8” RECOMMENDED CSS SETTINGS RANGE, 24” MAX FEED SIZE RECOMMENDED, BOLTED, HEAVY DUTY STEEL MAIN FRAME, CAST STEEL PITMAN WITH REPLACEABLE TOE PROTECTION, PRECISION MACHINED LARGE DIAMETER HIGH STRENGTH PITMAN SHAFT, 59” DIAMETER DUCTILE IRON CAST FLYWHEELS, LABRYINTH STYLE SEALS, HIGH LOAD CAPACITY SPHERICAL ROLLER BEARINGS, AUTO-LUBE GREASE PUMP WITH TIMER, AR CHEEK PLATES AND BARREL PROTECTOR, BROADTOOTH JAW DIES, 18% MANGANESE, BUILT-IN LIFT EYES FOR SAFE EXCHANGE, HYDRAULIC WEDGE ADJUSTMENT WITH CONTROL PACKAGE, TANK, PUMP, CONTROLS FOR CSS ADJUSTMENT AND CONTROL OF HYDRAULIC TENSION PRESSURE, PRESSURE SENSOR, ACCUMULATOR. AUTOMATIC HYDRAULIC OVER SPRING TOGGLE TENSIONING SYSTEM. MID-MOUNTING CONFIGURATION FOR PORTABLE PLANTS. JAW WEIGHT 59,500 LBS.
NON-DRIVE SIDE COMPOSITE GUARD. DRIVE SIDE COMPOSITE GUARD.
SPECIAL HEAVY DUTY JAW MOUNTING FOR SIDE MOUNT JAW.
54" X 20' SUPERIOR INTREPID VIBRATING GRIZZLY FEEDER, 40 HP 1200 TEFC. 110MM BEARINGS, OUTBOARD SPRING ARRANGEMENT, 0-DEGREE INCLINE, I-BEAM CONSTRUCTED MAIN BODY, 1” THICK PARENT PAN MATERIAL, 1/2” THICK AR LINER, 1/2” THICK SIDE LINERS, 5FT ARIZONA STYLE GRIZZLY BARS WITH AGGRESSIVE TAPER AND 4” SPACING.
AR LINED JAW DISCHARGE HOPPER WITH ADJUSTABLE WIPERS.
1" PLATE JAW FEED HOPPER 9' X 21'. ½” HOPPER LINERS -30” UP FROM BOTTOM, 10FT FORWARD.
½” LINERS ON HOPPER VERTICALS.
14" WF SUPPORT BEAMS UNDER HOPPER WITH DIAGONAL BRACES.
AR LINED 3/8" PL BY PASS CHUTE UNDER GRIZZLY AREA TO UNDER JAW CONVEYOR, WITH ADDED ROCK CLEARANCE PROVISION FOR REJECT CONVEYOR.
54" X 26' UNDER JAW CONVEYOR, 20HP TEFC:
- LAGGED CROWN HEAD PULLEY, SELF-CLEANING WING TAIL PULLEY.
- IMPACT SLIDER BED UNDER JAW AREA, THEN 36" SPACING ON CEMA C.
- 3 PLY BELT.
- DODGE SCM BEARINGS AND 2 15/16" ALLOY SHAFTS.
- FAB TEC HEAVY DUTY TAKE-UPS.
- ORANGE GUM RUBBER FLASHING
- RUBBER DISC RETURNS
- NON TEAR BELT, VULCANIZED BELT SPLICE, SUPERIOR XTERRA
FULL OBSERVATION STAND OVER JAW WITH DIAMOND PLATE FLOOR AND 42" HAND RAILS WITH ACCESS LADDERS, MAINTENANCE PLATFORM ON LOWER DECK.
SELF CLOSING SAFETY GATES AT LADDER OPENINGS.
SAFETY GUARDS, SAND BLASTED CHASSIS, RUST INHIBITOR PRIMER AND TWO FINISH COATS INCLUDED.
OPTIONS:
6 LEG FAB TEC PLANT MOUNTED HYDRAULIC STABILIZING SYSTEM: (NON RUN-ON)
- FAB TEC CYLINDERS 6” X 18” STROKE, 70,000 LB. CAPACITY WITH SAFETY-LOK
CIRCUIT.
- DELTA HPX-200 12-VOLT POWER UNIT (THIS IS THE PREFERRED POWER)
- (1) SPOOL VALVE~ NUMBER OF BANKS TO MATCH LEG QUANTITY.
- CYLINDER MOUNTING HARDWARE.
- HEAVY DUTY FOOT PADS.
SELF CONTAINED HONDA 8 HP HYD. POWER PACKAGE ~VS~ HPX 200 12V:
- ELECTRIC START.
- 12 GALLON HYDRAULIC RESERVOIR WITH FILTER PROTECTION.
- 2 1/2 GPM PUMP.
REMOVABLE 2 PLY RUBBER CURTAINS WITH CHANNEL AND FLAT BAR FRAME ON BOTH SIDES OF VGF:
- REMOVABLE.
- 1/2” X 4” FLAT BAR HANGERS.
- 6” CHANNEL WEIGHTS WITH SIDE CLAMPS.
SHEET IN TOP OF ¾' HOPPER PORTION WITH REMOVABLE 2 PLY RUBBER CURTAINS ON BOTH SIDES:
- REMOVES WITH HOPPER ONLY.
- 1/2” X 4” FLAT BAR HANGERS.
- 4” CHANNEL WEIGHTS WITH SIDE CLAMPS.
FOLDING HANDRAILS ON UPPER OBSERVATION PLATFORM:
- REQUIRES SMALLER RECTANGLE STYLE PLATFORM.
- A USER-FRIENDLY OPTION FOR TRANSPORT.
- DOES NOT REQUIRE COMPLETELY REMOVING UPPER DECK HANDRAILS FOR TRANSPORT.
- SKID MOUNT STYLE 54 X 20 VGF AND HOPPER MODULE:
- STANDARD REMOVABLE STYLE.
- NO LIFTING LEGS OR HYDRAULICS.
BOOSTER ATTACHMENT INSTALLED ON CHASSIS FOR EITHER PEERLESS BOOSTER:
AES ELECTRICAL SWITCHGEAR FOR 3055 JAW PLANT:
- 60 X 60 ENCLOSURE WITH CUSTOM CORD CAGE, LEG KIT AND 400 AMP MAIN WITH
OPERATOR-UPPER RH
- CORD CAGE
- NEMA RATED FVNR STARTERS WITH CIRCUIT BREAKERS
- 30 HP JAW DISCHARGE
- 20 HP SPARE 1 WITH 60 AMP RECEPTACLE
- 20 HP SPARE 2 WITH 60 AMP RECEPTACLE
- 7.5 HP GRIZZLY THRUS REJECT WITH 20 AMP RECEPTACLE
- 3 HP JAW ADJUST 2 POSITION SWITCH IN PANEL DOOR
- 200HP ABB SOFT START
- 40 HP ABB VFD
- 5 KVA TRANSFORMER WITH 20A 110V SERVICE OUTLET
- ALL BUTTONS IN DOOR WITH WIRELESS REMOTE CONTROL FOR VFD START/STOP,
SPEEDUP/DOWN, ESTOP, SAFETY STARTUP HORN (MANUAL), E-STOP, RADIO REMOTE
- 100' OF POWER CORD, SWITCHGEAR PANEL TO SET OFF PLANT 30'
- MAIN POWER CORD IS (3)PARALLEL RUN OF 3/0W FOR POWER PHASES, AND SINGLE 4/0W
FOR GROUND.
GUARDING - WE DO NOT WARRANT THAT MANUFACTURERS’ GUARDING WILL MEET ALL LOCAL CODES. IT IS THE RESPONSIBILITY OF THE END USER TO HAVE GUARDING CHECKED BY A LOCAL INSPECTOR, PRIOR TO STARTUP OF EQUIPMENT OPERATIONS, CORRECTIVE ACTIONS AND ASSOCIATED EXPENSE ARE THE RESPONSIBILITY OF THE END USER.