2023 SUPERIOR F3055J5420VGFCP

2023

SUPERIOR

F3055J5420VGFCP

2269538

Used

EQ0013272

Plant Specifications Construction Main frame constructed of wide flange structural beams Crusher Feed Box Constructed of 3/4" MS plate with 1/2" AR 400 weld-in liner Crusher Discharge Chute Mild steel construction with AR liners in wear areas Discharge Chute Skirting Replaceable 60 durometer skirt board rubber with clamp bars where required Feed Hopper Cartridge Feed Hopper and VGF cartridge is bolt- on, and may be removed if required for road transport. Please check local codes Feed Hopper Constructed of 3/4" AR400 wear plate with reinforced steel and sloped sidewalls, includes exterior side panels fitted with conveyor belt rubber to prevent access to VGF and assist in keeping debris or foreign material from entering the area Hopper Wings Manually folding extending hopper wings for increased hopper capacity, includes bolt on hinges and supports. Must be removed for road travel. Grizzly Fines Chute Constructed of 1/4" A36 plate with 1/4" AR400 weld-in liner Fines Chute Access Door Hinged side access door Fines Chute Skirting Replaceable 60 durometer skirt board rubber with clamp bars where required Walkway Platform(s) Lower crusher observation and maintenance platform and upper crusher observation platform Walkway Access Steep angle stair both sides of plant and stair access from lower platform to upper platform Access Gates Self closing hinged gates at all walkway access points Grease Package Remote grease station, multiple grease points outside of chassis frame Tool Box Aluminum tool box Cord Holders Round pipe with end disc style cord holders welded to chassis frame Paint Standard Superior paint - Graphite Gray (RAL 7024) chassis, Window Gray [RAL 7040] Jaw and VGF, Superior Orange guardrails and guarding Guarding For all drive and tail pulleys, guards may not meet all local codes; customer is responsible to have guarding inspected Chassis Specifications Axle Split Quad axle with (16) 11Rx22.5 radial tires and 8' spacing Suspension Spring suspension Brakes Complete air brake package Fifth Wheel Included Lights Brake and directional signals Mud Flaps Installed behind transport wheels Cribbing Legs (6) fixed structural steel cribbing legs Landing Gear (6) hydraulic Run-on leveling legs with 9 HP Honda Power Unit Tow Eye Not included Level Assist Not included Booster Axle Not included or equipped to accept a booster. Please consult Superior if a booster is required now or in the future Discharge Conveyor Belt Width 60" discharge conveyor Conveyor Orientation Rear Discharge (conveyor discharges over axle) Conveyor Support Fixed height discharge Conveyor Fold Not included Conveyor Construction Structural steel channel frame Drive Class I head end Gear Reducer Shaft mount Motor 20 HP motor TEFC Belt Speed 300 FPM Capacity 500 STPH of 100 PCF material Drive Pulley 16" diameter, 3/8" herringbone lagged CEMA crown faced drum Tail Pulley 14" diameter CEMA Chevron® wing pulley Bearings Dodge Load Area CEMA C, 5" dia. impact rolls, 12" spacing Trough Idlers CEMA C, 5" dia. steel rolls troughing idlers Returns CEMA C, 5" dia. steel rolls on 10' spacing Belting 3 ply 1/4 x 1/16 330 PIW Belt Splice Factory vulcanized belt splice Belt Scraper Superior Exterra® Primary Scraper Jaw Specifications Jaw Size Liberty 3055 Bolted Frame Jaw Jaw Drive 200 HP TEFC Crusher Duty Motor Operating Speed 230 RPM Capacity Range 300-835 STPH (270-760 MTPH) Nominal Feed Opening (tip to tip) 33" x 63" (840mm x 1600mm) Closed Side Setting 3.2" - 8" (80mm - 200mm) Max Feed Size 25.6" (650mm) V-Belt Drive 10 groove 8V-belt with drive guard Flywheel Guards Drive and non-drive side flywheel guards included Jaw dies Standard broad tooth, 18% Manganese pitman and stationary jaw dies with lifting eyes built in lifting eyes Setting Adj. and HPU Package Hydraulic wedge adjustment with control package. Includes tank, controls for CSS setting adjustment and hydraulic tension pressure, pressure sensor, and accumulator Tension system Automatic hydraulic over spring tension system Auto grease System Not included Bearing Sensors Not included VGF Specifications VGF Size Intrepid® 54" x 20' Vibrating Grizzly Feeder VGF Motor 40 HP TEFC VGF V-Belt Drive with drive guard Pan Liner Replaceable 1/2" thick AR liners Grizzly Dual 30" (5' total) stepped tines Springs Outboard spring mount arrangement Grizzly Spacing 3" nominal opening Electrical Specifications Voltage 460 v / 3 ph / 60 hz Control Panel Skid mounted panel, with lifting eyes. Travels on plant and removed for operation. Includes starters for all on-board motors and (2) additional #2 starters and NEMA rated components Wiring Factory supplied and installed wiring from panel to all on board motors. Customer responsible for wiring power into control panel, and additional starters Wireless Remote Not included Options: Rear Discharge Rear discharge (discharges over axle) instead of Front discharge (over kingpin) Hopper Wings Manually folding extended hopper wings for increased hopper capacity, includes bolt on hinges and supports, must be removed for road travel Hydraulic Run-On Legs Hydraulic Run-on leveling legs with 9 HP Honda Power Unit Lower Observation Platform Observation/service platform for access to the jaw auxiliary systems Upper Observation Platform Upper observation platform for viewing into the jaw, includes access from lower platform Self Closing Hinged Gate Self closing hinged gates at all walkway access points in lieu of sasfety chain Steep Angle Stairs Folding steep angle stairs for access to walkway Grease Stations Remote grease station, multiple grease points outside of chassis frame Tool Box Aluminum tool box Cord Holders Round pipe with end disc style cord holders welded to chassis frame Split Quad Axle Split Quad axle with (16) 11Rx22.5 radial tires and 8' spacing Control Panel Electrical control panel with NEMA rated components, including starters for all On-board motors and (2) extra #2 starters. Panel is wired to all on plant motors. Customer responsible to bring power to and wire in power cable Primary Scraper* Superior Exterra Primary Scrapers Vulcanized Splice* Factory vulcanized belt splice on conveyors Standard Liners Standard broad tooth, 18% Manganese pitman and stationary jaw dies with lifting eyes built in lifting eyes Stepped Tines 5' long stepped tines (max feed size is 24") 3" Bar Opening 3" nominal opening