USD $598,000
Machine Location:5141 Hwy 71 WestLa Grange, Texas, USA 78945(Opens in a new tab)
Seller Information
View Seller Information
General
Year
2021
Manufacturer
SUPERIOR
Model
6203T44PWP
Serial Number
1940771
Condition
Used
Description
SUPERIOR PORTABLE GUARDIAN® 6203 TWIN 44" AGGREDRY® WASH PLANT EQUIPPED AS PER BELOW:
PLANT SPECIFICATION:
- CONSTRUCTION: MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL BEAMS
- DISCHARGE CHUTE: MANUAL ROLLAWAY CHUTE CONSTRUCTED OF 1/4" STRUCTURAL STEEL WITH 1/4" WELD-IN AR 400 LINER
- BLENDING CAPABILITIES: 1/4 PANEL BLENDING GATES IN DISCHARGE CHUTE SYSTEM
- TOP DECK DISCHARGE: OVER THE KINGPIN OR BLENDS DOWN TO BOTTOM DECK CROSS CONVEYOR
- MIDDLE DECK DISCHARGE: TO MIDDLE DECK CROSS CONVEYOR OR BLEND DOWN TO BOTTOM DECK CROSS CONVEYOR
- BOTTOM DECK DISCHARGE: TO BOTTOM DECK CROSS CONVEYOR OR BLEND UP TO TOP DECK DISCHARGE
- WALKWAY: AROUND BOTH SIDES AND FEED END OF SCREEN; ENDS WHERE SCREEN MEETS DISCHARGE CHUTE, MANUALLY FOLDS ONE SIDE (NON-DRIVE SIDE)
- OBSERVATION PLATFORM: FOR THE DEWATERING SCREEN
- WALKWAY ACCESS: TO BOTH SIDES OF CHASSIS WITH (2) VERTICAL SLIDING LADDERS
- ACCESS GATES: SELF CLOSING HINGED GATES AT ALL WALKWAY ACCESS POINTS
- SLURRY HOPPER: FOLDS MANUALLY FOR TRANSPORT WITH (2) 2.5” WATER LINES
- GREASE PACKAGE: REMOTE GREASE STATION, MULTIPLE GREASE POINTS OUTSIDE OF CHASSIS FRAME
- SAFETY TIEOFF: OVERHEAD SAFETY TIE OFF POSTS WITH CABLE BETWEEN TWO POSTS
- GUARDING: FOR ALL DRIVE AND TAIL PULLEYS
CHASSIS SPECIFICATIONS:
- AXLE: QUAD AXLE WITH (16) 11RX22.5 RADIAL TIRES
- SUSPENSION: SPRING SUSPENSION
- BRAKES: COMPLETE AIR BRAKE PACKAGE
- FIFTH WHEEL: INCLUDED
- LIGHTS: BRAKE AND DIRECTIONAL SIGNALS
- MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS
- CRIBBING LEGS: (8) FIXED STRUCTURAL STEEL CRIBBING LEGS
- LANDING GEAR: 2-SPEED CRANK DOWN TO AIDE IN LIFTING OFF AND ATTACHING TO TRUCK
SPRAY SYSTEM AND UNDERFLUME
- UNDERFLUME CONSTRUCTION: ¼” AR PLATE
- UNDERFLUME SPRAY BARS: LOCATED AT FEED AND DISCHARGE POINTS
- MANIFOLD: 8” BOLT FLANGE FOR FRESH WATER HOOKUP
- MANIFOLD DISTRIBUTION: DISTRIBUTES WATER TO SCREEN SPRAY BARS, SLURRY HOPPER, FMW WASH BACK & FINES HOPPER
CROSS CONVEYOR SPECIFICATIONS
- CROSS CONVEYORS: (2) 30” X 12’ LONG SLIDE-IN REVERSING CROSS CONVEYORS
- DRIVE: CLASS II HEAD END
- GEAR REDUCER: DODGE SHAFT MOUNT
- MOTOR: 7.5 HP MOTOR(S) TEFC
- DRIVE PULLEY: 10” DIAMETER, DIAMOND LAGGED MD CROWN FACED DRUM
- TAIL PULLEY: 10” DIAMETER MD WING PULLEY
- BEARINGS: DODGE
- IDLERS: CEMA C, 5” DIA. ROLLS, SEALED FOR LIFE BALL BEARINGS, 20°
- BELTING: 3 PLY 3/16 X 1/16 330 PIW
- BELT SPLICE: FACTORY INSTALLED FLEXCO MECHANICAL FASTENER(S)
- BELT SCRAPER: (1) EXTERRA PRIMARY SCRAPER PER CROSS CONVEYOR
SCREEN SPECIFICATIONS
- SCREEN SIZE: GUARDIAN 6X20 3-DECK HORIZONTAL SCREEN
- SCREEN DRIVE: RIGHT HAND
- CONFIGURATION: OPERATE IN TRUE HORIZONTAL POSITION
- SCREEN MOTOR: 40 HP, TEFC, NEMA PREMIUM “DESIGN C”
- FOLDING MOTOR: MANUALLY FOLDING MOTOR FOR PLANT TO TRAVEL AT 12’6” WIDE
- SHAFT HOUSING: MILD STEEL PROTECTION CLAMPED TO SHAFT HOUSING
- SPRINGS: STANDARD COIL SPRINGS
- FEEDBOX: 24” FEEDBOX WITH ¼” AR LINERS
- SIDELINERS: STANDARD SCREEN SIDE-LINERS
- SCREEN MEDIA: CUSTOMER SUPPLIED AND INSTALLED
TOP DECK
- TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 4’ SINGLE CROWN WIRE CLOTH MEDIA SECTIONS
- TOP TAKE UP: STANDARD TAKE UP RAILS
MIDDLE DECK
- TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 4’ SINGLE CROWN WIRE CLOTH MEDIA SECTIONS
- MIDDLE TAKE UP: STANDARD TAKE UP RAILS
BOTTOM DECK
- TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 4’ SINGLE CROWN WIRE CLOTH MEDIA SECTIONS
- BOTTOM TAKE UP: STANDARD TAKE UP RAILS
MATERIAL WASH SPECIFICATIONS
- MATERIAL WASHERS: SUPERIOR TWIN 44” AGGREDRY® DEWATERING WASHERS
- SCREW SPEED: 17 RPM
- CAPACITY: UP TO 300 STPH (SUBJECT TO CHANGE BASED ON FINAL GRADATION)
- WEAR SHOES: RUBBER
- SCREW MOTOR: (2) 20 HP TEFC
- GEAR BOX: DODGE SHAFT MOUNT
- DEWATERING SCREEN: INTEGRATED 6X12 DEWATERING SCREEN
- DEWATERING SCREEN MOTOR: (2) 11.4 HP ELECTRIC VIBRATORS
- BOOSTER PUMP: (2) 15HP BOOSTER PUMP INCLUDING 2” BALL VALVE TO INCREASE & CONTROL FINES JET DISCHARGE PRESSURE
ELECTRICAL SPECIFICATIONS
- VOLTAGE: 460 V / 3 PH / 60 HZ
- PANEL ENCLOSURE: SKID MOUNTED PANEL, WITH LIFTING EYES. TRAVELS ON PLANT AND REMOVED FOR OPERATION
- COMPONENTS: NEMA WITH START/STOP PUSHBUTTONS, AMP METER, HOUR METER & WARNING LIGHT
- STARTERS: FOR ALL ON PLANT MOTORS, (2) ADDITIONAL #2 STARTERS (UP TO 25HP MOTORS), & VFD CONTROL FOR FMW MOTORS
- WIRING: FACTORY SUPPLIED AND INSTALLED WIRING FROM PANEL TO ALL ON BOARD MOTORS