2023 FAB TEC INC P400RD

2023

FAB TEC INC

P400RD

PC-3-529-23

New

E00066976

FABT/SUPE P400RD CONE PLANT EQUIPPED AS PER BELOW: 3 AXLE CARRIER 24" WF 84# BEAMS: - 9700 HUTCH SUSPENSION, TANDEM/TANDEM - 10' WIDE, 22,500# AXLES AND 11:OO X 22.5 TIRES - AIR BRAKES, LED TAIL LIGHTS, LED MARKER LIGHTS, LED STROBE LIGHT, RELFECTIVE TAPE AND MUD FLAPS - TEN GROUND SUPPORT STANDS - EXTRA HD BOOSTER ATTACHMENT FOR TANDEM TKAB2 BOOSTER - BOOSTER NOT INCLUDED HEAVY DUTY CONE MOUNT AND AR LINED UNDER CONE DISCHARGE HOPPER WITH 1/2" X 6" ADJUSTABLE WIPERS: - INSPECTION DOOR IN BACK OF HOPPER SELF SUPPORTING OVERSIZED HEX STYLE FEED RING IN LIEU OF STANDARD WALKWAYS AROUND CONE WITH DIAMOND PLATE FLOOR, TOE BOARDS, AND 42" TUBE STEEL HANDRAILS EXTENDED TO FRONT OF MOTORS SELF CLOSING SAFETY GATE AT LADDER OPENING 48" OVER REAR AXLES UNDER CONE CONVEYOR 15 HP TEFC: - 5207 FALK SHAFT MOUNT REDUCER ON ALLOY SHAFT - VULCANIZED LAGGED PULLEY, SELF-CLEANING WING TAIL PULLEY - 3-PLY BELTING WITH 1/4" COVER - 2 15/16 PILLOW BLOCK BEARINGS - CLOSE SETTING ON CEMA C IDLERS UNDER CONE, THEN 36" SPACING - FULL LENGTH SKIRT BOARD. FIRST 15' WITH FLASHING - 4'-6" OVERHAND AT THE DISCHARGE END FROM THE CHASSIS - GUIDE ROLLERS AT HEAD OF CONVEYOR - VULCANIZED BELT SPLICE - SUPERIOR X-TERRA BELT WIPER - RUBBER DISC RETURNS WITH GUARDS FAB-TEC 70K RUN-ON SYSTEM: - 18" STROKE CYLINDERS 70,000 LB CAPACITY (AT 2500 PSI) WITH SAFETY-LOK CIRCUIT - DELTA HPX-200 12-VOLT POWER UNIT - (1) SPOOL VALVE - NUMBER OF BANKS TO MATCH LEG QUANTITY - CYLINDER MOUNTING PLATES AND HARDWARE - HYEAVY DUTY FOOT PADS SELF-CONTAINED HONDA 8 HP HYD. POWER PACKAGE VS HPX 1200 12V: - ELECTRIC START - 12 GALLON HYDRAULIC RESERVOIR WITH FILTER PROTECTION - 2 1/2 GPM PUMP OBSERVATION STAND INCORPORATED INTO WALK-IN DRIVE GUARD: - FOR EASY CONE DRIVE MAINTNENANCE AND CONE FEED OBSERVATION PLATFORM IN FRONT OF CHASSIS WITH HANDRAILS: - DIAMOND PLATE DECK SPECIAL JACK SHAFT DRIVE FOR 400 HP MOTOR: - DODGE PX200 ELATOMERIC COUPLING - (2) 3 15/16 TYPE 'E' BEARINGS - 4 7/16" ALLOY SHAFT - ADDED STEEL FOR LOWER BEARING/SHEAVE MOUNT - ADDED GUARDING - OBSERVATION DECK INCORPORATED INTO GUARDING HINGED UNDER CONE CONVEYOR FOR MAINTENANCE (MANUAL) HYDRAULIC RAISE AND LOWER OF UNDER CONE CONVEYOR: - ACCOMPANIED BY LEG LEVELING HYDRAULICS ORANGE FLASHING VS STANDARD BLACK (FULL LENGTH) GREASE STATION FOR UNDER CONE CONVEYOR: - (2) POINTS DUE TO LENGHT OF LINES EXTRA PANEL STYLE GUARDING AROUND UNDER CONE CONVEYOR TAIL PULLEY SECTION COGGED BELT DRIVE: - CONE AND MOTOR SHEAVES, BUSHING AND DRIVE BELTS - CONE SHEAVES PROVIDED WITH CONE (2) TOOL BOX MOUNTED ON CHASSIS UNDER CONE CONVEYOR DISCHARGE WITH SPRAY BAR FOR DUST CONTROL: - 1 1/4" SPRAY BAR WITH FOG NOZZLES - INCLUDES MANIFOLD WITH GATE VALVE TO SPRAY BAR - INCORPORATED INTO HEAD PULLEY GUARDS TO SPRAY MATERIAL FALLING OFF OF CONVEYOR - PUMP NOT INCLUDED CONE SPECIFICATIONS: - CRUSHER MODEL: P400 - CONE MOTOR: (1) 400 HP TEFC CRUSHER DUTY MOTOR - MOTOR BASE: ADJUSTABLE MOTOR BASE WITH ENCLOSED DRIVE - COUNTERSHAFT BLOW: CREATES A POSITIVE PRESSURE INSIDE COUNTERSHAFT BOX TO PREVENT MATERIAL CONTAMINATION - AUTOMATION: VANTAGE AUTOMATION WITH 100' TETHER - BACKUP PUMP: BACK UP LUBE PUMP, HPU INTEGRATED - COLD WEATHER KIT: COLD WEATHER KIT INCLUDING ADDITIONAL RELAYS FOR PUMPS AND HEATERS, AND ONE ADDITIONAL TANK HEATER - LINER BACKING: LINERS SHIP INSTALLED AND BACKING MATERIAL POURED - LINER CONFIGURATION: STANDARD MEDIUM LINERS - MANGANESE CONTENT: LINERS ARE 18% MANGANESE CONTENT - HPU: HYDRAULIC POWER UNIT WITH FABRICATED STEEL 50 GALLON TANK, AND SUBMERGED GEAR TYPE PUMP, MOUNTED ON CHASSIS - LUBE UNIT: PACKAGE LUBE ASSEMBLY WITH 120 GALLON TANK AND 54 GPM SUBMERGED GEAR TYPE PUMP, MOUNTED ON CHASSIS - AIR COOLER: AIR TYPE LUBE SYSTEM OIL COOLER, RELIEF VALVE AND RELATED COOLER PRICING - VOLTAGE: 480V/3PH/60HZ PAINT: - PAINTED GRAPHITE GRAY WITH SAFETY YELLOW GUARDING AES ELECTRICAL CUSTOM SWITCHGEAR, PANEL SETS OFF PLANT 25' TO EITHER SIDE 60x60 BACK PANEL AND ENCLOSURE CORD CAGE 800 AMP MAIN BREAKER WITH OPERATOR LOCATED IN UPPER RIGHT HAND CORNER 100 FT PENDANT 100 FT OF MAIN POWER CORD E-STOPS LOCATED IN PENDANT AND PANEL DOOR 800 WATT PANEL HEATER 120 VOLT GFCI SERVICE OUTLET HOUR METER VOLTS, HERTZ, AND AMP METERS IN PANEL DOOR 400 HP CONE (596.25 FLA) PROTECTED BY MAIN BREAKER 400 HP PSTX SOFTSTART 10 HP LUBE PUMP (14 FLA) 25 AMP BREAKER SIZE 1 STARTER 10 HP HYDRAULIC PUMP (14 FLA) 25 AMP BREAKER SIZE 1 STARTER NO CONTROLS - PLC CONTROLLED 5 HP COOLING FAN (7.6 FLA) 15 AMP BREAKER SIZE 1 STARTER NO CONTROLS - PLC CONTROLLED 1/3 HP COUNTERSHAFT BLOWER 15 AMP BREAKER SIZE 00 STARTER NO CONTROLS - PLC CONTROLLED TANK HEATER FEED 15 AMP BREAKER HYDRAULIC TANK HEATER 15 AMP BREAKER 20 HP DISCHARGE (27 FLA) 60 AMP BREAKER SIZE 2 STARTER 20 HP FEED CONVEYOR (27 FLA) 60 AMP BREAKER SIZE 2 STARTER WIRED TO 60 AMP HUBBELL RECEPTACLE 20 HP RETURN CONVEYOR (27 FLA) 60 AMP BREAKER SIZE 2 STARTER WIRED TO 60 AMP HUBBELL RECEPTACLE 5 KVA TRANSFORMER 15 AMP BREKAER FOR THE PRIMARY 40 AMP 120 V BREAKER FOR THE SECONDARY 20 AMP 120 V BREAKER FOR GFCI 15 AMP 120 V BREAKER FOR CONTROL POWER 10 AMP 120 V BREAKER FOR PANEL HEATER **INTERLOCKS **FEED CONVEYOR INTERLOCKED TO THE CONE AND DISCHARGE - GUARDING: FOR DRIVE AND TAIL PULLEYS, V-BELT DRIVE AND RETURN IDLERS. GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO HAVE GUARDING INSPECTED.