2019 CATERPILLAR D6

2019

CATERPILLAR

D6

9,335

Used

3093

D3494

This machine is a D6 XL WH with NEUTRAL Hours: 3890, CAT C9.8 ACERT Engine, Engine Block Heater, Automatic 4 Speed Transmission, Cab (ROPS) with A/C, Differential Steer, Engine Air Pre-Cleaner, Waste Handling (Landfill) Arrangement, SALT Undercarriage, 24" Trapezoidal Shoes, Final Drive Seal Guards, Pivot Shaft Seal Guards, SU Blade With Trash Rack, Automatic Reversing Fan, Drawbar, Fuel Tank Guards, Heavy Duty Bottom Guards, CAT Slope Indicate, LED Flood Light Arrangement, Ripper Ready Ansul Fire Suppression, Powered Cab Pre-Cleaner, Rated at 255 HP, Weight 54,000 LBS. Repair/Condition Report: The following are repairs completed by the CAT Dealer prior to Marcel Equipment owning the machine; At 513 hours, performed 500 hour service At 1,032 hours, performed 1,000 hour service At 1,491 hours, performed 500 hour service At 2,094 hours, performed 2,000 hour service At 2,513 hours, performed 500 hour service At 3,091 hours, performed 1,000 hour service At 3,538 hours, performed 500 hour service At 4,051 hours, performed 2,000 hour service At 4,542 hours, performed 500 hour service At 5,071 hours, performed 1,000 hour service At 5,580 hours, performed 500 hour service At 5,651 hours, performed DPF service & valve set At 5,651 hours, installed NEW DEF injector & spark plug At 5,651 hours, installed NEW thermostat At 6,048 hours, performed 2,000 hour service At 6,305 hours, performed update for condenser fans At 6,305 hours, REBUILT both lift cylinders At 6,543 hours, performed 500 hour service At 6,719 hours, installed NEW a/c condenser At 6,875 hours, installed NEW injector wiring harness At 6,913 hours, installed NEW DPF pressure sensors At 7,046 hours, performed 1,000 hour service At 7,083 hours, installed NEW ARD head & spark plug At 7,358 hours, installed NEW undercarriage At 7,414 hours, installed NEW engine ECM At 7,502 hours, performed 500 hour service At 8,048 hours, performed 2,000 hour service At 8,261 hours, installed NEW parking brake solenoid At 8,261 hours, installed NEW NOX sensors At 8,261 hours, installed NEW DEF manifold At 8,510 hours, performed 500 hour service At 8,792 hours, replaced oil cooler At 8,792 hours, REBUILT transmission oil pump At 8,792 hours, REBUILT transmission At 8,792 hours, REBUILT torque converter At 9,027 hours, performed 1,000 hour service The following was completed by Marcel Equipment; Upon arrival to our yard, machine was stripped for power washing Machine was inspected visually & operationally Engine oil filter was cut open - clean Transmission filter was cut open - clean Hydraulic filter was cut open - clean Magnets & suction screens checked - clean Final drive oils were checked - levels good & oils clean Engine was serviced Transmission, hydraulic & final drive oils were changed Replaced DEF pump & tank filters The following pressures were taken to ensure within OEM spec; Engine low/high RPM Stall speed Engine oil pressures - high/low Fuel pressure Engine boost Transmission pump pressure - high/low Transmission lube pressure - high/low Torque converter inlet & outlet - high/low Lock-up clutch pressure Pilot pressure Main relief pressure Steering stand by pressure Brake pressures Accumulators Fan speed - max/min Steering cut-out The following repairs were completed by Marcel Equipment; Completed bearing roll-in for main & rods Engine oil pump disassembled, inspected & resealed Resealed engine oil pan Installed NEW a/c dryer Replaced required hoses/lines Installed NEW window spray nozzles Installed NEW DEF injector Installed NEW DEF manifold Installed NEW bearings for lift cylinder yoke mounts Had DPF filter field cleaned Removed & cleaned engine pre-cleaner Installed NEW track cannon seals Disassembled, inspected & resealed final drives Installed NEW final drive seal guards Resealed starter motor Tightened blade joints where required w/ NEW pins & bearings Calibrated blade Installed belly pans Completed required cab repairs HVAC system cleaned & serviced Batteries tested & connections serviced Completed required cosmetic & welding repairs Complete machine was sand blasted, primed, painted & new decals applied Fire suppression will be certified before shipment Machine has been completed & is work ready!

Enclosed