MYR RM1,439,849
Seller Information
View Seller InformationGeneral
Manufacturer
SUPERIOR
Model
GUARDIAN 7X20
Serial Number
1948853/2053814
Condition
Used
Stock Number
1163/1255
Description
ON LEASE
Equipment As Follows:
Superior Guardian 7x20 3 Deck Horizontal Screen SN 2053814
1. Unit Specifications
Screen size-7'x20' three deck triple shaft horizontal screen
Slope angle-Set at true horizontal (0 degrees)
Movement-High G-force screen with adjustable speed and stroke
Bearings-190mm spherical roller bearings with 38 gears
Springs-Standard coil springs
Suspension Damper-VS2 system
Motor Base-Slide adjustment motor base [less motor]
Body Construction-Huck bolted body constructed of 5/16" structural steel side plates
Discharge lips-6" discharge lips with 1/4" AR liners
Feedbox-24" feedbox with 1/4" AR liners
Inspection Ports-Bolt-on inspection ports and spray hole knockouts
Shaft Housing Protection-Standard mild steel protection clamped to shaft housing
Paint-Superior Class 1 - (1) coat primer; (1) top coat enamel, Greyhawk Beige 12-01156 for screen box and base frame (if included), and motor base
2. Drive Specifications
Drive-Right hand drive (standard)
Motor-50 HP, TEFC, NEMA Premium "Design C"
V-Belt Drive-With drive guard and tension system
Tuning Kit-Tuning kit included
Voltage-460 v / 3 ph / 60 hz
3. Top Deck Specifications
Top Deck-4' heavy crown deck, with thicker longitudinal bars: Max feed size is 14"
Screen media-Supplied and installed by customer
Take Up-Standard take up rails
4. Second Deck Specifications
Second Deck-Heavy x-brace single crown deck to accommodate 4' single crown wire cloth media sections
Screen media-Supplied and installed by customer
Take Up-Standard take up rails
5. Bottom Deck Specifications
Bottom Deck-End Tension Bottom Deck
Screen media-Supplied and installed by customer
Take Up-Standard take up rails
Superior Chassis SN 1948853
1. Plant Specifications
Construction- Main frame constructed of wide flange structural beams
Discharge chute- Manual rollaway chute constructed of ¼” structural steel with ¼” weld-in AR 400 liner
Blending capacity- ¼ panel blending gates in discharge chute system
Top deck discharge- over the kingpin or blends down to middle deck cross conveyor
Middle deck discharge- To middle deck cross conveyor or blend down to bottom deck cross conveyor
Bottom Deck Discharge- To bottom deck cross conveyor or blend up to middle deck cross conveyor
Walkway- Walkway around both sides and feed end of screen: extends out to the end of the discharge chute, manually folds one side (non-drive side)
Walkway access- Access to both sides of chassis with (2) removable aluminum ladders
Access gates- Self closing hinged gates at all walkway access points
Handrail- Welded square handrail with toe kicks
Grease package- Remote grease station, multiple grease points outside of chassis frame
Cord holders- Round pipe with end disc style cord holders welded to chassis frame
Safety tie off- Overhead safety tie off posts with cable between two posts
Paint- Standard Superior paint - Superior Beige 12-00619 w/ yellow guarding
Guarding- For all drive and tail pulleys, guards may not meet all local codes; customer is responsible to have guarding inspected
2. Chassis Specifications
Axle- Tandem axle with (8) 11Rx22.5 radial tires
Suspension- Spring suspension
Brakes- Complete air brake package
Fifth wheel- Included
Lights- Brake and directional signals
Mud flaps- Installed behind transport wheels
Cribbing legs- (4) fixed structural steel cribbing legs
Landing gear- Hydraulic lift-only leveling legs with 9 HP Honda Power Unit
3. Fines Hopper and Conveyor
Hopper Construction- 1/4" AR plate steel sides
Fines Hopper Liner- Under-screen hopper side wall lined with rubber wear liners
Gathering Trough- Full length with adjustable rubber flashing
Conveyor Size- 60" wide fines discharge conveyor
Conveyor Construction- Structural steel channel main frame
Drive- Class I head end
Gear reducer- Dodge shaft mount
Motor- 15 HP TEFC
Drive pulley- 12" diameter, 3/8" herringbone lagged MD drum
Tail pulley- 12" diameter, CEMA Chevron® wing pulley
Bearings- Dodge
Trough idlers- CEMA C, 5" dia. Rolls, sealed for life ball bearings
Returns- CEMA C, 5" dia. Steel rolls on 10' spacing
Belting- 3 ply 3/16 x 1/16 330 PIW
Belt splice- Factory installed Flexco mechanical fastener
Belt scraper- Superior Exterra® primary belt scraper
4. Cross Conveyor Specifications
Cross Conveyors- (2) 30" x 12' long slide-in reversing cross conveyors
Drive- Class I head end
Gear reducer- Dodge shaft mount
Motor- 7.5 HP motor(s) TEFC
Drive pulley- 10" diameter, 3/8" diamond lagged MD crown faced drum
Tail pulley- 10" diameter CEMA wing pulley
Bearings- Dodge SCM
Idlers- CEMA B, 5" dia. Rolls, sealed for life ball bearings, 20°
Belting- 3 ply 3/16 x 1/16 330 PIW
Belt splice- Factory installed Flexco mechanical fastener(s)
Belt scraper- (1) Exterra Primary scraper per cross conveyor
5. Electrical Specifications
Voltage- 460 v / 3ph / 60 hz
Panel enclosure- skid mounted panel, with lifting eyes. Travels on plant and removed for operation
Components- NEMA components, with start/stop push buttons, amp meter, hour meter and warning light
Starters- starters for all on plant motors and (2) additional #2 starters (up to 25 HP motors)
Wiring- factory supplied and installed wiring from panel to all on board motors. Customer responsible for wiring power into control panel, and additional starters
6. Paint
GreyHawk Beige 12-001156 with yellow guarding
On-Site Start-up, Training and Warranty Commissioning
• RB Scott will supply a field service technician to complete startup