2022 TEREX FINLAY I140RS

2022

TEREX FINLAY

I140RS

TRX140RST0MN37718

New

E00060943

FINLAY I-140RS TRACKED IMPACTOR PLANT EQUIPPED AS PER BELOW: ENGINE: - TIER 4 FINAL: SCANIA DC13 368KW (500HP) ENGINE IMPACT CHAMBER: - TEREX CR032 IMPACT CHAMBER - FULLY HYDRAULICALLY ASSISTED APRON SETTING AND HYDRAULIC APRON RELEASE - MANUAL RAISE CHAMBER FLAP ALLOWING EXTRA INLET CLEARANCE - 4 BAR ROTOR - TOOL STEEL BLOW BARS 2 HIGH & 2 LOW - DIRECT DRIVE VIA CLUTCH - DRIVE BELT TENSIONER WHEEL - BLOW BAR LIFTING TOOL SUPPLIED - TIP SPEED RANGE 35-44 M/SEC (115-144FT./SEC) - SMALLER DRIVE PULLEY FITTED TO GIVE A ROTOR TIP SPEED RANGE OF 31-39M/SEC (102-128FT./SEC) STANDARD LARGE PULLEY STILL DISPATCHED WITH MACHINE - HYDRAULIC RAISE OF CHAMBER INLET FLAP - ROTOR FITTE WITH (2) FULL MATENSITIC CERAMIC & 2 LOW MARTENSITIC BLOW BARS HOPPER & FEEDER: - VGF FIXED HOPPER - STEPPED GRIZZLY FEEDER WITH INTEGRAL PRE-SCREEN, STANDARD 50MM SPACING - MESH APERTURE ON GRIZZLY FEEDER: 38MM (1.50") - SELECTABLE DISCHARGE TO BY-PASS CONVEYOR OR MAIN CONVEYOR - BLANKING MAT FOR VGF - PRE-SCREEN TOP DECK FITTED WITH SIDE TENSIONED MESH, 30MM APERTURE STANDARD - INDEPENDENT PRE-SCREEN C/W HYDRAULICALLY FOLDING AND LOCKING HOPPER AND BLANKING MAT, 50MM CASSETTE SPACING * 38MM MESH AS STANDARD - INDPENDENT PRE-SCREEN HOPPER EXTENSIONS - PRE-SCREEN PUNCH PLATE OPTIONAL SPACING - 25MM/50MM/75MM - NEED TO SPECIFY MAIN CONVEYOR: - 1300MM (51") BELT FULL LENGTH - PIPED FOR OVERBAND MAGNET - HYDRAULIC RAISE/LOWER FOR MAGNET - UNDER CRUSHER VIBRATORY FEEDER WITH WEAR RESISTANT STEEL LINERS (C/W SHORTENED MAIN CONVEYOR) AUXILARY: - BYPASS CONVEYOR WITH 80MM WIDE PLAIN BELT, DISCHARGING TO THE RHS OF THE MACHINE - TWIN POLE OVERBAN MAGNET C/W STAINLESS STEEL SKIRTING & STAINLESS STEEL DISCHARGE CHUTE, DISCHARGING RHS OF THE MACHINE RS COMPONENTS: - 4.88M X 1.52M (16' X 5') SINGLE DECK AFTER SCREEN C/W 40MM MESH AS STANDARD UNLESS OTHERWISE STATED - 500MM (20") WIDE BELT TRANSFER CONVEYOR - 500MM (20") WIDE BELT HYDRAULIC FOLDING RE-CIRCULATING CONVEYOR ABLE TO SLEW FOR STOCKPILING OVERSIZE MATERIAL - 1400MM (55") WIDE BELT FINES CONVEYOR - RAPID DETACH AFTER SCREEN SYSTEM FOR FLEXIBILITY - BELT WEIGHER BELT SCALE CLIMCATE SPEC: - STANDARD OILS (RECOMMENDED FOR AMBIENT TEMPERATURES BETWEE -5 TO +30 DEG. C DUST SUPPRESSION: - PIPED FOR DUST SUPPRESSION C/W SPRAY BARS - WATER PUMP NOT INCLUDED ELECTRICAL: - EMERGENCY STOPS - HAND HELD TRACK CONTROL SET WITH CONNECTION LEAD - RADIO REMOTE SYSTEM: OPERATIONAL CONTROLS OF MACHIN (AUTO START/STOP) & TRACK MOVEMENT - PRESSURISED AIR SYSTEM FOR ELECTRICAL CONTROL CABINET GENERAL: - SAFETY GUARDS IN COMPLIANCE WITH MACHINERY DIRECTIVE - AUXILIARY DRIVE